ChrisMinelli Posted April 26, 2020 Report Share Posted April 26, 2020 What do you all use for greasing your water pump? The guy at NAPA didn’t know what I was talking about. Thanks in advance! Quote Link to comment Share on other sites More sharing options...
captden29 Posted April 26, 2020 Report Share Posted April 26, 2020 I always use what I am using for my wheel bearings. never had a problem.very few people know much technical info about all the different greases available at the auto parts stores. that includes me. I use lucas red and tacky for my boat trailer bearings. towed the boat to ny from NC many times. if that grease is good for that it will handle a water pump. I do know that you need to be careful not to pump too much into the water pump zerk. capt den Quote Link to comment Share on other sites More sharing options...
Plymouthy Adams Posted April 26, 2020 Report Share Posted April 26, 2020 (edited) water pump grease is special and not much used in cars today so most OTC places do not stock, most common substitute today is the stuff found at outdoor centers as used in the outboard engine foot.. Edited April 26, 2020 by Plymouthy Adams Quote Link to comment Share on other sites More sharing options...
T120 Posted April 26, 2020 Report Share Posted April 26, 2020 (edited) I use Lubriplate 115 - last time I purchased it some years ago it was about $12.50. Edited April 26, 2020 by T120 Quote Link to comment Share on other sites More sharing options...
greg g Posted April 26, 2020 Report Share Posted April 26, 2020 Have a can in the garage from my father's basement looks to be 40 to 50s vintage can. Some folks have said they are using marine lower unit lube or boat trailer wheel bearing grease. 1 Quote Link to comment Share on other sites More sharing options...
keithb7 Posted April 26, 2020 Report Share Posted April 26, 2020 (edited) Where is this water pump grease nipple you speak of? My '53 and '54 flatheads do not seem to have one. I suspect they changed the design in later years and dropped the grease requirement? Edited April 26, 2020 by keithb7 Quote Link to comment Share on other sites More sharing options...
plymouthcranbrook Posted April 26, 2020 Report Share Posted April 26, 2020 7 minutes ago, keithb7 said: Where is this water pump grease nipple you speak of? My '53 and '54 flatheads do not seem to have one. I suspect they changed the design in later years and dropped the grease requirement? My older water pump I replaced years ago had one but the NAPA replacement did not. Newer model I suspect Quote Link to comment Share on other sites More sharing options...
desoto1939 Posted April 26, 2020 Report Share Posted April 26, 2020 I agree with Captdne I used a boat propeller grease in mine. Since a propeller is under water at all times this is a good grease to use. You can get this grease at any Walmart store. Also be careful to not over grease the bearing with the old style bronze bushing this will cause the pump to leak. Just a small amount will do the trick. I have changed out my factory pump that had the bronze bushing to a sealed bearing bushing so I do not have to worry about greasing the unit. If you have the older or should I say the more newer style pump that these newer pumps by gates are now coming with the sealed bearing. I would suggest that if your old pump starts to leak then replace with a sealed bearing. Rich Hartung[ Quote Link to comment Share on other sites More sharing options...
desoto1939 Posted April 26, 2020 Report Share Posted April 26, 2020 The guys that say their pump does not have a grease fitting or nipple it would be located on the output shat on the body just before the flange that is used to bolt on the fan blade assembly. So your unit might be a sealed bearing unit and th epump was replaced at sometime before you got the car maybe by a prior owner. Rich Hartung Quote Link to comment Share on other sites More sharing options...
greg g Posted April 26, 2020 Report Share Posted April 26, 2020 There was a zero fitting on the shaft casting. Most replacements made since the mid sixty's have "perminently lubricated" from the factory. Quote Link to comment Share on other sites More sharing options...
ChrisMinelli Posted April 26, 2020 Author Report Share Posted April 26, 2020 1 hour ago, keithb7 said: Where is this water pump grease nipple you speak of? My '53 and '54 flatheads do not seem to have one. I suspect they changed the design in later years and dropped the grease requirement? my water pump is almost certainly original to the engine. The fitting is pretty apparent if you stand on the driver’s side and look down at the pump. You may have a replacement. I’m just cheap and want to get as much use out of the original as possible. The service manual discussed “water pump grease” which is noted as a different formulation than chassis lube. On Ford Model A’s the grease is water soluble because it sometimes comes in contact with the coolant. I do not know if that is the case with the Chrysler water pump. I do know that my radiator is not working all that swell and I’m sure I’ll find plenty of sludge in it and the water distribution tube when I work on them later this summer. Quote Link to comment Share on other sites More sharing options...
ChrisMinelli Posted April 26, 2020 Author Report Share Posted April 26, 2020 @keithb7 1 Quote Link to comment Share on other sites More sharing options...
Sniper Posted April 26, 2020 Report Share Posted April 26, 2020 2 hours ago, T120 said: I use Lubriplate 115 - last time I purchased it some years ago it was about $12.50. If you go to Lubriplate they have a "where to buy" search function, or you can buy it direct, about the same price still. 1 Quote Link to comment Share on other sites More sharing options...
Nick307 Posted April 26, 2020 Report Share Posted April 26, 2020 Any marine application grease marked for extreme pressure should work. You just need an EP grease with a corrosion inhibitor. Quote Link to comment Share on other sites More sharing options...
Los_Control Posted April 26, 2020 Report Share Posted April 26, 2020 1 hour ago, greg g said: There was a zero fitting on the shaft casting. Most replacements made since the mid sixty's have "perminently lubricated" from the factory. Must be just about when they figured out they would make more money if parts failed. Personally I figure the grease really wont last long in a original water pump, going to need a few squirts every time it starts leaking. Why not use cheap grease so it will get flushed out and have a fresh supply as long as it is being maintained? Just my two cents. Even cheap grease today is probably better then what was available when these vehicles were built. Currently working on a old john deere garden tractor. Just amazed the pulley/shafts on the deck have zirk fittings for grease, but the bearings inside are sealed bearings. Grease the shaft all you want and get a good feeling, those bearings are not getting grease. I do think this is intentional for parts to wear out, and then need replaced after the product is sold. Quote Link to comment Share on other sites More sharing options...
Dodgeb4ya Posted April 26, 2020 Report Share Posted April 26, 2020 (edited) Why not just use the correct grease if needed...easy to find..https://www.ebay.com/itm/Water-Pump-Grease-500g-tub/322605609036?hash=item4b1ccaf04c:g:~L0AAOSwlw1dsx21 I bought a full NOS 1/2 gallon off ebay for $20.00 10 years ago. Another small can for five which I use all the time.. The right stuff for the job. Edited April 26, 2020 by Dodgeb4ya 1 Quote Link to comment Share on other sites More sharing options...
Nick307 Posted April 26, 2020 Report Share Posted April 26, 2020 10 minutes ago, Dodgeb4ya said: Why not just use the correct grease if needed...easy to find..https://www.ebay.com/itm/Water-Pump-Grease-500g-tub/322605609036?hash=item4b1ccaf04c:g:~L0AAOSwlw1dsx21 I bought a full NOS 1/2 gallon off ebay for $20.00 10 years ago. Another small can for five which I use all the time.. The right stuff for the job. Sometimes what is available today is more important then what you can get tomorrow. I mean if you're gonna go that far then you might as well start looking for gas made in the 50's as well. Quote Link to comment Share on other sites More sharing options...
Sniper Posted April 26, 2020 Report Share Posted April 26, 2020 Lubriplate 115 is for water pumps Quote Link to comment Share on other sites More sharing options...
Dan Hiebert Posted April 26, 2020 Report Share Posted April 26, 2020 Our D24 has a "newer" replacement water pump without the grease fitting, but our Terraplane has one that requires "water pump grease". I got the blank stare at all the auto parts places here, too. I got a tube of marine grade grease at Tractor Supply Co. It is for lower units of boat motors, greasing propeller shafts, boat trailer wheel bearings, ATV applications, etc. Anything where the grease may come in contact with water. Marine grade / water pump grease is formulated not to emulsify with water when it comes in contact with it. 1 Quote Link to comment Share on other sites More sharing options...
T120 Posted April 26, 2020 Report Share Posted April 26, 2020 (edited) 1 hour ago, Dodgeb4ya said: Why not just use the correct grease if needed...easy to find..https://www.ebay.com/itm/Water-Pump-Grease-500g-tub/322605609036?hash=item4b1ccaf04c:g:~L0AAOSwlw1dsx21 I bought a full NOS 1/2 gallon off ebay for $20.00 10 years ago. Another small can for five which I use all the time.. The right stuff for the job. When I bought Lubriplate 115, 15 years ago or so, it came in a can. Still have two cans on the shelf in the garage, more than I'll ever use. Nowadays collectors pay more for a can that is labelled Water Pump Grease - don't care if it's empty. lol Edited April 26, 2020 by T120 spelling 1 Quote Link to comment Share on other sites More sharing options...
Dodgeb4ya Posted April 27, 2020 Report Share Posted April 27, 2020 Hey Nick307 did you even read the link I posted? ? https://www.ebay.com/itm/Water-Pump-Grease-500g-tub/322605609036?hash=item4b1ccaf04c:g:~L0AAOSwlw1dsx21 It's the modern day water pump grease you just go and buy it.... real simple if that's what someone wants. That's why I posted it I like cool old stuff and that's why I posted my tubs of WP grease.... guess you don't like good quality old stuff .... Don't beat down the old timers....you are new here... be nice. You will appreciate it here. 2 1 Quote Link to comment Share on other sites More sharing options...
Nick307 Posted April 27, 2020 Report Share Posted April 27, 2020 Not trying to beat anybody down. If you can get the right stuff then by all means you should. But if you can't then knowing you have options for alternatives should be known. Not trying to start nothing, just saying. Quote Link to comment Share on other sites More sharing options...
Andydodge Posted April 27, 2020 Report Share Posted April 27, 2020 (edited) After you have enjoyed the blank stares of the parts kid when asking for water pump grease go in for the kill and ask for a points file............sheer bliss...........lol........andyd Edited April 27, 2020 by Andydodge 3 3 Quote Link to comment Share on other sites More sharing options...
greg g Posted April 27, 2020 Report Share Posted April 27, 2020 (edited) Want to see blank stares? Go to Advance autozonoriellies and ask for a points file.... Edited April 27, 2020 by greg g Quote Link to comment Share on other sites More sharing options...
Desert Rat Posted October 18, 2022 Report Share Posted October 18, 2022 I discovered a new noise recently that was the water pump. Found some water pump grease on Amazon. I've read not to put "too much" grease in.. So how much is too much? I estimate I've put in maybe a teaspoon judging by what came out of the gun.. The noise has gotten better but hasn't completely gone away. Next question is what happens when you use too much? I may end up buying a water pump after all trying to figure this out. Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.