40desoto Posted July 9, 2013 Report Share Posted July 9, 2013 Im currently have my flathead at a friends machine shop and planning in getting the motor rebuilt. I know its a 25in block, and according to the previous owner its the original engine for the car. The numbers have been replaced so there is not telling what the size of the motor is? I took of the head to measure the bore size but was unable to get an accurate measurement. Is there any other way of telling what size motor is is? Im very impatient and want to know whether to keep this motor (if its rebuildable) or purchase a larger 50's mopar flathead six. Here is what my question is, I saw this post omn the hamb and was wondering if this is really a big issue on these motors and how I can go about mentioning this to the shop.. "That the bad thing about Plymouth/Dodge six cylinder engines is that the oil line from the main gallery is drilled straight through. So as much oil goes to the cam bearings as the mains and rods. The fix is to tap the feed to the cam and install a restriction. Maybe with a 1/16 hole. Then the crank gets what it needs. Quote Link to comment Share on other sites More sharing options...
TodFitch Posted July 9, 2013 Report Share Posted July 9, 2013 The quote was about a Plymouth/Dodge engine but the 25" engine, at least in the US, was used for DeSoto and Chrysler. But I don't think there is a big difference in the way the oiling system is designed (other than possible provision for full flow oil filter). I'm only a shade tree mechanic and I've not built up an engine for high performance, so I am probably missing something. But if the pressure in the main gallery is sufficient then it seems likely that the crank main bearings should be getting enough oil regardless of how much oil is going through the cam bearings. And the pressure in the main gallery is what is measured by the oil pressure gauge on the dash. So I would take that quote from the HAMB with a grain of salt. Quote Link to comment Share on other sites More sharing options...
P15-D24 Posted July 9, 2013 Report Share Posted July 9, 2013 I think this is referring to the fact that out of spec cam bearing can be responsible for low oil pressure. Their were aftermarket gadgets that would be bolted into the oil gallery hole to restrict the oil flow to the cam bearings and help maintain pressure. They were tube about 3 inches long with different size tips on the end for each cam bearing. The obvious solution is if you are getting the engine rebuilt replace the cam bearings. I don't think the original statement "... is that the oil line from the main gallery is drilled straight through." is actually bad! Quote Link to comment Share on other sites More sharing options...
Don Coatney Posted July 9, 2013 Report Share Posted July 9, 2013 What numbers have been replaced? Do you have a service manual for your car? Per my book if your engine is original you have a 228.1 CI engine. I would think that your friend at the machine shop would be able to measure your engine and tell you if it is worth rebuilding. If what you read on the HAMB posting were true I would think that the streets would be lined with dead mopar flathead engines. The factory engine oiling system works well unless you plan on spinning your engine above the red line for extended periods. 1 Quote Link to comment Share on other sites More sharing options...
Plymouthy Adams Posted July 9, 2013 Report Share Posted July 9, 2013 a set of inside mics will be needed to measure the bore..the stroke can also be measured to see if the engine has been upped in CI by way of rod/crank swap.. Quote Link to comment Share on other sites More sharing options...
40desoto Posted July 10, 2013 Author Report Share Posted July 10, 2013 I think this is referring to the fact that out of spec cam bearing can be responsible for low oil pressure. Their were aftermarket gadgets that would be bolted into the oil gallery hole to restrict the oil flow to the cam bearings and help maintain pressure. They were tube about 3 inches long with different size tips on the end for each cam bearing. The obvious solution is if you are getting the engine rebuilt replace the cam bearings. I don't think the original statement "... is that the oil line from the main gallery is drilled straight through." is actually bad! Thank you for some clarification. Do you think ist worth telling the rebuilder to add these aftermarket gadgets in the oil gallery hole? or should I even worry about it and just clarify to him to replace the cam bearings? Quote Link to comment Share on other sites More sharing options...
Dave72dt Posted July 10, 2013 Report Share Posted July 10, 2013 A stock engine should have little need for those aftermarket pieces. Cam bearings need lube too. New brgs and mike the cam journals for wear. Out of spec journals, replace the cam. Make sure the oil pump is in good condition. Every brg is a controlled leak and the pump must have adequate flow to compensate for them. Worn parts increase the leak flow. Owner suggested lube system mods MAY void your warranty. Quote Link to comment Share on other sites More sharing options...
greg g Posted July 10, 2013 Report Share Posted July 10, 2013 Perhaps your over stamp is a attempt to match a non factory engine with registration owner documents as lots of jurisdictions used the engine number for vehicle ID. Usually a commercial rebuilder would have affixed a tag to the engine with some sort of indication what was done internally. Desoto engines during the 40's were either 228 or 236 cu in, the stroke was the same. 3 3/8 for 228, 3 7/16 for 236. Oversized pistons resulting from and overbore during a rebuild are usually stamped with a size indicator on the top of the piston. Getting good micrometer reading of the rod a main journals will also tell you if the journals have been cut necessitating non standard bearings. All of these measurements should be easy to attain. Now unless some one swapped in 251 rotating components (crank and rods) your stroke measurement should be 4 1/4 for engines built in the 40's regardless of bore. 251 engines had 3 7/16 bore with a 4 1/2 in stroke. Your factory oiling system should be find unless you are building an engine that is gong to operate consistently above 4000 RPM, but with any of these log stroke engines, building on that way is usually not the way to go for street operation. Long stroke equals torque, which is what gets a vehicle moving.. Basically you are rebuilding 6 Briggs and Stratton engines in a row, its best not to over complicate the process. Quote Link to comment Share on other sites More sharing options...
_shel_ny Posted July 10, 2013 Report Share Posted July 10, 2013 I think this is referring to the fact that out of spec cam bearing can be responsible for low oil pressure. Their were aftermarket gadgets that would be bolted into the oil gallery hole to restrict the oil flow to the cam bearings and help maintain pressure. They were tube about 3 inches long with different size tips on the end for each cam bearing. The obvious solution is if you are getting the engine rebuilt replace the cam bearings. I don't think the original statement "... is that the oil line from the main gallery is drilled straight through." is actually bad! Pic of some of the aftermarket tubes, with a nifty installation/removal tool. Quote Link to comment Share on other sites More sharing options...
P15-D24 Posted July 10, 2013 Report Share Posted July 10, 2013 Pic of some of the aftermarket tubes, with a nifty installation/removal tool. Yep, that's them! Pulled them out of few engine cores. Think the are made by Textron ? I have a full set with instructions just haven't been able to find them. Quote Link to comment Share on other sites More sharing options...
De Soto Frank Posted July 25, 2013 Report Share Posted July 25, 2013 Greg's on-target with the bore/ stroke info... '37-'41 De Sotos originally came with a 228 cid engine: 3-3/8" bore x 4-1/4" stroke. '42-'50 (at least) had a larger bore: 3-7/16" x 4-1/4" stroke, for 236 cid. I have heard that 3-3/8" pistons are getting hard to find, and expensive, so you might want to have your shop measure the bores and check parts avails before committing to machine work on your block. It might be a little cheaper to find a decent 236 De Soto or 251 Chrysler six, that uses the 3-7/16" pistons, and re-do that one.Good luck ! Quote Link to comment Share on other sites More sharing options...
40desoto Posted July 25, 2013 Author Report Share Posted July 25, 2013 Thanks for all the input guys!! I shared most of these comments to the shop doing my engine. Desoto Frank, Are you sure 34-41 desotos all came with the 228 cid engine? when I have called places that carry the parts they state that they either came with 228 or 236 cid. I guess Ill know when the bore gets measured. Quote Link to comment Share on other sites More sharing options...
De Soto Frank Posted July 26, 2013 Report Share Posted July 26, 2013 The 236 didn't come along until 1942. The 1941 and earlier De Sotos going back to 1934 or so used either the 228 cid, or a few years used the 241 cid that Chrysler used in their big sixes through 1941: this engine is also a 3-3/8" bore, but with a 4-1/2" stroke. Quote Link to comment Share on other sites More sharing options...
40desoto Posted July 26, 2013 Author Report Share Posted July 26, 2013 Thank you Frank.. The shop is currently checking the bore size before ordering the parts for a complete engine rebuild. Any recommendations on rebuilding a 1940 228 ? head milling,oil gallery hoe restriction, etc etc that I should consider doing since the engine is being rebuild? I plan on ordering a Deluxe rebuild kit from Kanter or ordering all the parts included from Andy Bernbaum any recommendations? Im trying to catch the Andy Bernbaum %10 off special through the end of July.. In case it matters Ill be using a 1986 S10 5 speed transmission (non-world class) and a rear end from a 1973 Plymouth Satellite Quote Link to comment Share on other sites More sharing options...
De Soto Frank Posted July 26, 2013 Report Share Posted July 26, 2013 I don't think you need to worry about making oil gallery restrctions. Properly re-built, the Flahead MoPar is a sturdy, durable engine. Make sure the coolant passages are thoroughly rodded / cleaned-out ( all freeze-plugs removed, all rust & sludges raked/flushed out of the water jackets).The other caution is with setting the end-gaps in the piston rings. The spec in the MoPar and other period shop-manuals is suspect.The period shop literature suggests a ring end-gap of 0.007". Many modern rebuilders feel that this is way too tight, and the the engine comes-up to operating temperature, the ends butt, the ring continues to expand, causing binding, scoring, and possible ring / ring-land breakage. Most flat-head MoPars were reb-built and rebored before 50,000 miles... probably from this original set-up.Most modern authorities recommend allowing 0.0035" end-gap per each inch of bore diameter. The stock bore on a 228 six is 3-3/8", or 3.375" x 0.0035" = 0.0118" minimum end-gap, or 0.012", rounded.Check-out the following from Hastings, a manufacturer of quality piston rings for over 75 years:http://www.hastingsmfg.com/ServiceTips/ring_gaps.htm Beyond this,. the usual careful attention to cleanliness and careful re=assembly and pre-lube should put you in good stead.After break-in, running the engine on good, modern detergent oils should result in good, long engine life. The 228 is modest in terms of power, rating somewhere around 105 HP @ 3600 RPM, but should have decent torque. Let us know what the shop tells you on the bore sizing... 1 Quote Link to comment Share on other sites More sharing options...
Bryan Posted June 12, 2022 Report Share Posted June 12, 2022 On 7/10/2013 at 3:20 PM, P15-D24 said: Yep, that's them! Pulled them out of few engine cores. Think the are made by Textron ? I have a full set with instructions just haven't been able to find them. Did you find any engines where the oil gallery to the camshaft started out 5/16" and ended at a 1/4" before it reached the camshaft? Quote Link to comment Share on other sites More sharing options...
Yulio Rodriguez Posted October 2, 2022 Report Share Posted October 2, 2022 On 7/26/2013 at 1:42 PM, De Soto Frank said: I don't think you need to worry about making oil gallery restrctions. Properly re-built, the Flahead MoPar is a sturdy, durable engine. Make sure the coolant passages are thoroughly rodded / cleaned-out ( all freeze-plugs removed, all rust & sludges raked/flushed out of the water jackets). The other caution is with setting the end-gaps in the piston rings. The spec in the MoPar and other period shop-manuals is suspect. The period shop literature suggests a ring end-gap of 0.007". Many modern rebuilders feel that this is way too tight, and the the engine comes-up to operating temperature, the ends butt, the ring continues to expand, causing binding, scoring, and possible ring / ring-land breakage. Most flat-head MoPars were reb-built and rebored before 50,000 miles... probably from this original set-up. Most modern authorities recommend allowing 0.0035" end-gap per each inch of bore diameter. The stock bore on a 228 six is 3-3/8", or 3.375" x 0.0035" = 0.0118" minimum end-gap, or 0.012", rounded. Check-out the following from Hastings, a manufacturer of quality piston rings for over 75 years:http://www.hastingsmfg.com/ServiceTips/ring_gaps.htm Beyond this,. the usual careful attention to cleanliness and careful re=assembly and pre-lube should put you in good stead. After break-in, running the engine on good, modern detergent oils should result in good, long engine life. The 228 is modest in terms of power, rating somewhere around 105 HP @ 3600 RPM, but should have decent torque. Let us know what the shop tells you on the bore sizing... Hello Frank, I have a DeSoto 1958 model Diplomat and I’m looking to buy an engine rebuild kit, pistons, piston rings and other components. Can you or anyone point me on the right direction as to where I can get a rebuild kit ? It has a flathead 6 cylinders engine, I have attached pictures of the engine and car. I have the car in Cuba and I want to make sure I bring the right parts to keep my classic running. Thank you in advance ? 1 Quote Link to comment Share on other sites More sharing options...
andyd Posted October 2, 2022 Report Share Posted October 2, 2022 Yulio......welcome aboard........I'd try Andy Bernbaums, www.oldmoparts.com ...........I have dealt with them for over 30yrs and they have always been good, your car looks nice in the pic......regards from Australia......andyd Quote Link to comment Share on other sites More sharing options...
keithb7 Posted October 3, 2022 Report Share Posted October 3, 2022 (edited) I am not aware of anyone that offers a “rebuild kit” for a flathead Mopar. Engine rebuilds vary wildly. Many get new bearings and gaskets, a hone and new rings and call it rebuilt. Others much more. New Valves. Tappets. Valve guides. Camshaft and new cam bushings. Timing chain set. Main bearings. New pistons. Bore over. Oil pump. Expansion plugs. Etc etc. After a complete disassembly and thorough inspection with measuring tools, then you can determine the level of rebuild it needs. Or cut a few corners to “try and save a few dollars up front”. Meaning you are likely deferring the dollars today that will likely cost you a lot more later. When I rebuilt my engine I guess I assembled my own rebuild kit. Some parts from Andy Bernbaum. Some from Vintage Power Wagons. Some from Rock Auto. Nobody could supply the 0.001 polished rod bearings I needed. Those came from E-bay. NOS. It is a bit of work. It can take time if you are inexperienced. To get it right and know exactly what you need, and the proper sizes. Or if you are keen to learn, books and experiments in the garage on a spare engine worked out extremely well for me. I learned a ton. I had the most fun in a long time. The lessons and the experience were priceless. I sometimes wish I had another one to rebuild. Edited October 3, 2022 by keithb7 Quote Link to comment Share on other sites More sharing options...
andyd Posted October 3, 2022 Report Share Posted October 3, 2022 Yulio.as Keith mentions no one actually has a "complete" side valve mopar "kit" tho' as Keith mentions places like Vintage Power Wagons, Rock Auto & ebay as well as Bernbaums may or could have what you need......... .............when I was chasing parts for the 230 engine I was building I ended up getting most of the parts from ebay however what I did was to determine exactly what years and specific models that the 230 or 3 & 1/4 bore engine was used and regularly search ebay using those years or models and I ended up getting pistons, rings, bearings both big end and main, valves, lifters, springs, timing chain and gears, oil pump and various other bit & pieces from all over the world....... ..............I would assume that your car, being a DeSoto uses the 25" long Chrysler/DeSoto engine which is similar to but DIFFERENT to the Plymouth/Dodge 23" long engine........whilst the 25" engine was only used in the Chrysler/DeSoto brands in the USA built cars, in Canada it was used in virtually all Mopar brands including both Dodge and Pymouth as well as both DeSoto & Chrysler together with the various truck lines in Canada including Dodge and Fargo........ ...............a similar situation occured here in Australia with the same reason as Canada being that as Canada & Australia had relatively small markets it made more sense to just offer the one engine in all 4 brands which resulted in the larger 25" DeSoto Chrysler engine being more common......... ...............I mention this as this info can help when searching for parts, even tho' the " ebay listing" may not mention that the parts suit a 1958 DeSoto your knowledge that the parts will suit may help to ensure you find what you need........... .........before I would chase up engine parts if I were you I'd determine exactly what engine you have ideally via disassembly or at least measuring the bore & stroke to get an idea of what it is .............I just looked into some reference books and for 1958 USA DeSoto's all had V8's.........and a DeSoto Diplomat was not listed in the USA models...........BUT.......where are you?..............and where was your car made as here in Oz the DeSoto brand DID use the "Diplomat" model name at least until 1956...............what is the engine, and body numbers on your car?............the engine number is stamped into a raised pad on the engine block above where the generator is and should start with "S".................. same with the body or chassis number .........have you any pics showing the side & rear view of the car?......... ................andyd Quote Link to comment Share on other sites More sharing options...
Merle Coggins Posted October 3, 2022 Report Share Posted October 3, 2022 (edited) I believe Kanter Auto Products has engine rebuild kits. I don't know what is all included in them, but it may be what you need. www.kanter.com Edited October 3, 2022 by Merle Coggins Quote Link to comment Share on other sites More sharing options...
SteveR Posted October 3, 2022 Report Share Posted October 3, 2022 (edited) 16 hours ago, andyd said: I'd try Andy Bernbaums, www.oldmoparts.com Be careful when ordering from them if you are overseas. They have a standard shipping rate of $65. I was going to order a Clutch Centering Tool at $4-5. Then I noticed the shipping for that tool was $65. I made a tool on my lathe. Edited October 3, 2022 by SteveR Quote Link to comment Share on other sites More sharing options...
9 foot box Posted October 3, 2022 Report Share Posted October 3, 2022 Cleggengine.com and oldpartssource.com have rebuild kits, once you know bore, bearing sizes and which rear main seal that you have. eokd mop218 is a parts number. Quote Link to comment Share on other sites More sharing options...
Marcel Backs Posted October 4, 2022 Report Share Posted October 4, 2022 My rebuilder used "Sealed Power" engine rebuild components on my 218. They are proper parts and not off shore repro schwag. Cheap insurance to assure long term reliability! M Quote Link to comment Share on other sites More sharing options...
andyd Posted October 4, 2022 Report Share Posted October 4, 2022 I'd still like more info on exactly what the car is........my John Lee's Standard Catalog of Chrysler 1924 to 1990 doesn't list a 1958 DeSoto Diplomat.........at least by that model name anyway.........andyd Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.