Sniper

Yeah, I saw them, but to be honest once I saw no heater or AC I moved on from the engine compartment.

I took two years of French, way back in 81-82 and I slept in a Holiday Inn Express Wednesday, so hold my beer. In any case, there is a large groove that prohibits any movement of the steering wheel on the column on cars equipped with steering gears. To center the steering wheel, you have to act on the tie rods equally, if you shorten one by 2 turns, you will have to lengthen the other by 2 turns. Anyway, there is a large groove that prohibits any movement of the steering wheel on the column on cars with a steering box. To center the steering wheel you have to act on the tie rods, if you shorten one of the 2 turns, you will have to lengthen the other by 2 turns.

Heck it's been my observation that the taxi companies buy used police cars and finish running them into the ground

Why would you need a replacement?

When it comes to taxes they got what they need to get what they want. Out here in Texas they decide how much tax you pay doesn't matter what you bought the car for.

You know, I haven't had a match since Superman died.

Don't happen to have any muriatic acid in a leaky bottle anywhere around? Similar happened to me when the wife stored some in the garage for the winter, it was used to balance the pool PH.

That is the exact on I used, not 100% sure a 41 Dodge has the same speedo connection as my 51 Plymouth, but I would roll the dice and get it, lol.

Lol, obviously they aren't car people as it is well known that with few exceptions you will never break even, much less make more. A 48 Plymouth isn't one of those exceptions either.

Put an ATP Y803 in my 51 Plymouth, a bit long for my needs but probably fits yours as well. This one is a 7/8-18 female (trans end) to 5/8-18 female (speedometer end). Same one would work in my 65 Cuda as well so that was the common sizes for MoPars back then. As for what a TH350 takes, dunno, I don't speak GM. So I go to look at what a 79 El Camino takes and guess what? ATP 803 is listed as fitting, lol.

I have to wonder if this had any documentation as an actual police car? Because all those 12 volt accessories did not exist in 1948.

Aside from the cost aspect I don't really see any downside to this. But to be honest with you if I were going to do it I do the remote filter setup and use a coolant rated filter. The coolant filters themselves aren't really much more expensive than a good oil filter. And to be honest you don't need to change them nearly as often. The ones I looked at were rated at 150,000 miles and as often as we drive our cars that would be our lifetime's most likely LOL

They make them with or without conditioner and either type is rated at 30 microns, I looked at all that.

The gauges should have worked fine. oil and water are mechanical, ammeter doesn't care about voltage and the fuel gauge should be the older style thermostatic type that runs on current flow not voltage.

Seems coolant filters are common in the diesel world. https://www.baldwinfilters.com/us/en/solutions/cooling-system-filtration.html https://www.donaldson.com/en-us/engine/filters/products/coolant/replacement-filters/donaldson-blue-filters/ https://www.wixfilters.com/Products.aspx?ct=phcf Not sure if it makes any monetary sense for us, but then again nothing with our hobby usually makes monetary sense.

Sorry, I got distracted. Went out and looked, it's located low in the block between the distributor and the oil fill tube. It usually is a pipe plug, that 4 sided bung you mentioned. I usuallt replace them with a drain cock that has a nipple to attach a drain hose.

Yes there is one on the block down by the distributor

Altitude will affect that level. I am at about 1600 feet and I can get 21" no problem. https://www.motor.com/magazine-summary/mastering-the-basics-reading-a-vacuum-gauge/ Here you can see my vacuum level

Induction heater, probably help with exhaust manifold nuts too. Lots of options on Amazon.

Wen was young and dumb I had a 64 300 with a 413. When I needed to take the block to the machine shop I just picked it up and put it in the back of my Daytona. When I got to the shop I picked it up again, carried it inside and put in on the counter. Asked the lady where she wanted it i, she gave me an odd look and said right there is fine/ Net morning I woke up and the trapzoid muscle across my right shoulder was hollering at me. That was in 1988, to this day if I work to hard that muscle makes itself known, lol. I never weighed that block, but the internet tells me they weight about 220lbs. You got a lot of cast iron in that block my friend.

Looks like it's a half assed job. Look at the rear shocks. I mean, you put in a different rear axle and some rusty shocks? Lots of little, attention to details things like that in this offer.

What Dave said. The thermostat sets the minimum operating temperature. If you're running too hot, and "middle of the gauge" really means nothing, then there is an issue elsewhere. Put a thermometer in the coolant and see what it is. Very generally speaking, high running temps at low road speeds is usually an air flow issue. As a rule of thumb, if you can put a piece of paper up against the outside of the radiator and the fan holds it there it's usually ok. My 51 had an issue, turned out there was a lot of very fine dust packed onto the fins of the radiator. So while the airflow was sufficient, the heat transfer was impeded by the dirt. A good hosing out of the fins fixed it. High running temps at highway speeds is usually a water flow issue. Check that the coolant level is good and the thermostat isn't partially closed. Sometimes the impeller on the pump comes loose or has eroded away. Wrong pulleys got installed at some point, belt is slipping, etc. My 51 had a 4 blade fan, Chrysler, at some point, put 6 bladed fans on these engines. I don't know their reasoning but it may apply to your situation. Of course this assumes the water jacket isn't full of crud and we all know that happens.

Don't think that can happen with the flatheads. Just won't run right.

Good point, I was going to buy a floor pan from the Plymouth Doctor, alas, I can no longer do that. If I win the Mega-millions I might try to buy and resurrect some of these old suppliers, lol.

Why? You're not doing anything useful running that one