Clarksville Windsor Posted October 13, 2017 Report Share Posted October 13, 2017 New topic: Water pump removal. Just had a broken valve spring fixed and car runs great.........Well, now that I've been running it, it now has now developed a leak at the water pump. It looks like the leak is coming from where the fan pulley attaches to the water pump. How difficult is it to remove/repair/reinstall the water pump? When I was just looking at the water pump housing, it seems like the cylinder head is in the way of removing a bolt to take off the water pump assembly--unless that is a bolt that is for the back plate of the water pump (maybe called 'cover plate'??? not sure if I am using the correct nomenclature). I wouldn't think that the head would be in the way for any bolts that hold on the water pump assembly. When reading the 1949-1950 Chrysler shop manual it didn't mention anything about the head being in the way. Here is exactly what the manual says for the REMOVAL AND INSTALLATION OF WATER PUMP: (1) Drain cooling system; (2) Remove fan belt and disconnect water pump hose; (3) Remove bolts holding water pump to engine block and lift out water pump and fan assembly. Is it really that easy? Am I just making is seem complicated? I am looking forward to some suggestions. Thanks Guys! On another note, where can I find the parts that I need for my car? I have been using Andy Bernbaum, but I've had difficulty with their customer service when they sent me the wrong part...its been over 3 weeks and still haven't received the correct part (I am not exaggerating) but they charged me immediately for the wrong part.... 1 Quote Link to comment Share on other sites More sharing options...
P15-D24 Posted October 13, 2017 Report Share Posted October 13, 2017 It's really that easy. Just watch the sharp edges on the backside of the radiator. Quote Link to comment Share on other sites More sharing options...
Clarksville Windsor Posted October 13, 2017 Author Report Share Posted October 13, 2017 What years/makes/models are the water pumps interchangeable for my 1950 Chrysler? It is a flathead 6 Spitfire. Quote Link to comment Share on other sites More sharing options...
Plymouthy Adams Posted October 13, 2017 Report Share Posted October 13, 2017 8 hours ago, Clarksville Windsor said: .......................Is it really that easy? Am I just making is seem complicated? ................. yes, time to slip back into the age of simplicity..... Quote Link to comment Share on other sites More sharing options...
Andydodge Posted October 13, 2017 Report Share Posted October 13, 2017 Clarksville.........my listings shows that Chrysler 6's used the same water pump from 1936 to 1954, same one that Plymouth & Dodge used from 1935-1950.........I know that the water pumps that are now sold have an improved circular impeller and sealed non greasable bearings rather than the old style impeller that had a pair of opposing blades and used greasable bushings...........the old style impellers also had rebuild kits available and I can remember having to redo the rebuild job as there was a fibre washer that had a tendency to break..........the water pumps I've seen listed on ebay all seem to be the new type but check around....I obtained a new pump for the 41 Plymouth I had a few years ago and it was the new style...........a much better design........whilst you are playing water pumps, check the condition of the water distribution tube that lives behind the water pump in the block......if its corroded then it should be replaced although you may curse me for this suggestion as it can be a PITA job..........just make sure you get the correct water tube which "should" be to suit the 25" engine which your Chrysler should have........also worth checking the condition of the radiator hoses including whether you have a metal lower tube or coiled wire inside a one piece lower hose.....either maybe present..........depending on clearance between the radiator and the fan its sometimes better/easier to remove the fan from the fan hub then take it off, usually four 1/2" bolts then you can usually see where the water pump bolts are.............its worthwhile using a piece of cardboard to push the removed bolts into so that you can see which go where as they are different lengths..............also note that some water may come out of the block from some bolt holes.....make a NOTE of which ones..............then once the pump is removed the backing plate can be taken off and is usually cleaned up and used with a new gasket on the new water pump.............if you are not sure which bolts leaked water then work on the principle that they ALL go into the water jacket and after cleaning the bolt threads use some pipe sealer or Permatex type gasket Goo to coat the threads on all bolts and reinstall.............I think that there are torque settings for these bolts but so long as they are done up tight you should be good to go.............trust this helps........welcome & regards from Oz.......Andy Douglas 1 Quote Link to comment Share on other sites More sharing options...
knuckleharley Posted October 13, 2017 Report Share Posted October 13, 2017 10 hours ago, Clarksville Windsor said: Is it really that easy? Yes. You can trust the factory shop manual and Motors Automobile Repair Manuals. If they tell you something is that simple,it is that simple. My only additional suggestions would be to tape a piece of cardboard cut to the size of the radiator core to the radiator to keep from accidentally damaging any fins accidentally, as well as to save the skin on your hands. Old radiator cores are nasty things,and they create nasty,infected cuts that make your hands sore. The next thing to do is remove the fan before you loosen the fan belt or do anything else. Putting the fan back on should be the next to last thing you do,and removing the cardboard should be the last thing you do. Don't ask me how I know this. 3 1 Quote Link to comment Share on other sites More sharing options...
plymjim Posted October 13, 2017 Report Share Posted October 13, 2017 As to your other question, a good source of parts is Roberts Motor Parts phone: 978 363 5407. I've had great luck dealing with them. You would also be surprised at how much stuff is available at your local Auto Zone, NAPA, Advance Auto stores, etc. 1 Quote Link to comment Share on other sites More sharing options...
Allmyjunk Posted October 13, 2017 Report Share Posted October 13, 2017 I know it's a little extra work but 4 bolts and 2 hose clamps later and the raidaitor is out of the way, atleast that is how I did it in my 48, much easier than fighting with it. Quote Link to comment Share on other sites More sharing options...
plymouthcranbrook Posted October 13, 2017 Report Share Posted October 13, 2017 I bought one for mine from NAPA about 12 years ago and never any problems with install or operation. Quote Link to comment Share on other sites More sharing options...
Clarksville Windsor Posted October 13, 2017 Author Report Share Posted October 13, 2017 11 hours ago, Andydodge said: Clarksville.........my listings shows that Chrysler 6's used the same water pump from 1936 to 1954, same one that Plymouth & Dodge used from 1935-1950.........I know that the water pumps that are now sold have an improved circular impeller and sealed non greasable bearings rather than the old style impeller that had a pair of opposing blades and used greasable bushings...........the old style impellers also had rebuild kits available and I can remember having to redo the rebuild job as there was a fibre washer that had a tendency to break..........the water pumps I've seen listed on ebay all seem to be the new type but check around....I obtained a new pump for the 41 Plymouth I had a few years ago and it was the new style...........a much better design........whilst you are playing water pumps, check the condition of the water distribution tube that lives behind the water pump in the block......if its corroded then it should be replaced although you may curse me for this suggestion as it can be a PITA job..........just make sure you get the correct water tube which "should" be to suit the 25" engine which your Chrysler should have........also worth checking the condition of the radiator hoses including whether you have a metal lower tube or coiled wire inside a one piece lower hose.....either maybe present..........depending on clearance between the radiator and the fan its sometimes better/easier to remove the fan from the fan hub then take it off, usually four 1/2" bolts then you can usually see where the water pump bolts are.............its worthwhile using a piece of cardboard to push the removed bolts into so that you can see which go where as they are different lengths..............also note that some water may come out of the block from some bolt holes.....make a NOTE of which ones..............then once the pump is removed the backing plate can be taken off and is usually cleaned up and used with a new gasket on the new water pump.............if you are not sure which bolts leaked water then work on the principle that they ALL go into the water jacket and after cleaning the bolt threads use some pipe sealer or Permatex type gasket Goo to coat the threads on all bolts and reinstall.............I think that there are torque settings for these bolts but so long as they are done up tight you should be good to go.............trust this helps........welcome & regards from Oz.......Andy Douglas I really appreciate all these suggestions and instructions. I've done things with some newer vehicles like my 86 CJ7... I personally converted my Straight 6 from the Carter carburetor to an EFI system using a late 90's 4.3 L Vortec wiring harness from an s-10. Lots of technical work, some air intake adapter plates,installing an ecm, fuel pressure lines, electric fuel pump, etc etc etc, but I haven't done anything with these older cars. I'm a pretty quick learner with some helpful guys that have experience , but when something is new to , it's like trying to hold a baby for the first time.... I don't want to break it . I really appreciate all of these suggestions and advice that everybody has given me. This blog is very helpful to me thanks to all of you. I just wish I knew how to reply to the individual comments when I have a specific question. For example, if "Billy Bob" told me to put a screw-on, I would like to be able to specifically respond to "Billy Bob", but I don't know how to do that.. Quote Link to comment Share on other sites More sharing options...
Frank Elder Posted October 14, 2017 Report Share Posted October 14, 2017 Scroll to the bottom of billy bob's advice and in RED LETTERS it says quote, click on that and reply. There are 2 different gaskets one for internal bypass and one for external bypass make sure you have the right one. 1 Quote Link to comment Share on other sites More sharing options...
Frank Elder Posted October 14, 2017 Report Share Posted October 14, 2017 See the extra hole on the left pump. Quote Link to comment Share on other sites More sharing options...
Jorge La Porta Posted November 11, 2017 Report Share Posted November 11, 2017 I am new on this forum, so first of all let me thank administradors to let me in..................I have a Plymouth Special Deluxe 1949 P18, i rebuilted the car for 6 years and now it is running weel, but some problens are appearing from time to time. Water pump is one of them, engine and water pump are originals and water circulating is working well, no leak when engine running but few ours after engine stop it is possible to see a leak in the back of water pump, i guess in the midle of it. I did gasket replacement one time during water pump rebuild but problem is still there. So please any help will be wellcome. Thanks Quote Link to comment Share on other sites More sharing options...
knuckleharley Posted November 11, 2017 Report Share Posted November 11, 2017 3 minutes ago, Jorge La Porta said: I am new on this forum, so first of all let me thank administradors to let me in..................I have a Plymouth Special Deluxe 1949 P18, i rebuilted the car for 6 years and now it is running weel, but some problens are appearing from time to time. Water pump is one of them, engine and water pump are originals and water circulating is working well, no leak when engine running but few ours after engine stop it is possible to see a leak in the back of water pump, i guess in the midle of it. I did gasket replacement one time during water pump rebuild but problem is still there. So please any help will be wellcome. Thanks Jorge,you need to rebuild the pump. The shaft and/or shaft bushing is worn,and when they start leaking like you described,that is a early warning that the pump is going to fail soon and that you need to rebuild or replace it. One thing is for certain,the leak is only going to keep getting worse. Quote Link to comment Share on other sites More sharing options...
Jorge La Porta Posted November 11, 2017 Report Share Posted November 11, 2017 I already did it during mechanical rebuilding, I do not thing problem is in the internal parts (i replace the shaft and shaft bushing recently). The leak is on the back of the pump, betwen pump back and head and as I wrote no leak while engine is running. Maybe you are right about but when I saw pictures above I do imagine metal plate behind my P18 pump can have some holes too. Do you think it is possible? Quote Link to comment Share on other sites More sharing options...
Jerry Roberts Posted November 12, 2017 Report Share Posted November 12, 2017 '... I do imagine metal plate behind my P18 pump can have some holes too. Do you think it is possible? " Yes it is possible , I had one with holes on another make of car . Did you seal the gasket on the back on both sides ? Quote Link to comment Share on other sites More sharing options...
Clarksville Windsor Posted November 12, 2017 Author Report Share Posted November 12, 2017 3 hours ago, Jorge La Porta said: I already did it during mechanical rebuilding, I do not thing problem is in the internal parts (i replace the shaft and shaft bushing recently). The leak is on the back of the pump, betwen pump back and head and as I wrote no leak while engine is running. Maybe you are right about but when I saw pictures above I do imagine metal plate behind my P18 pump can have some holes too. Do you think it is possible? I just replaced my water pump on my 1950 Windsor. One of the bolts on the backing plate on my new water pump was loose . So whoever put that backplate on that water pump at the factory, didn't tighten the bolts enough. I tightened them just a little and it worked after that. Mine stopped leaking right away. I hope you will have the same result. Quote Link to comment Share on other sites More sharing options...
Jerry Roberts Posted November 12, 2017 Report Share Posted November 12, 2017 (edited) Also at least one of the bolts that mount the water pump to the engine goes into the water jacket . Did you seal the threads ? On the backing plate , I usually remove the plate and use sealant on both surfaces . Edited November 12, 2017 by Jerry Roberts Quote Link to comment Share on other sites More sharing options...
Fernando Mendes Posted November 12, 2017 Report Share Posted November 12, 2017 On 12/10/2017 at 11:28 PM, Clarksville Windsor said: New topic: Water pump removal. Just had a broken valve spring fixed and car runs great.........Well, now that I've been running it, it now has now developed a leak at the water pump. It looks like the leak is coming from where the fan pulley attaches to the water pump. How difficult is it to remove/repair/reinstall the water pump? When I was just looking at the water pump housing, it seems like the cylinder head is in the way of removing a bolt to take off the water pump assembly--unless that is a bolt that is for the back plate of the water pump (maybe called 'cover plate'??? not sure if I am using the correct nomenclature). I wouldn't think that the head would be in the way for any bolts that hold on the water pump assembly. When reading the 1949-1950 Chrysler shop manual it didn't mention anything about the head being in the way. Here is exactly what the manual says for the REMOVAL AND INSTALLATION OF WATER PUMP: (1) Drain cooling system; (2) Remove fan belt and disconnect water pump hose; (3) Remove bolts holding water pump to engine block and lift out water pump and fan assembly. Is it really that easy? Am I just making is seem complicated? I am looking forward to some suggestions. Thanks Guys! On another note, where can I find the parts that I need for my car? I have been using Andy Bernbaum, but I've had difficulty with their customer service when they sent me the wrong part...its been over 3 weeks and still haven't received the correct part (I am not exaggerating) but they charged me immediately for the wrong part.... Quote Link to comment Share on other sites More sharing options...
Jorge La Porta Posted November 12, 2017 Report Share Posted November 12, 2017 Thank you all about water pump information, I will work on it and I will observe all advices about seal the threads on the backing plate and gasket seal too, possible holes on backplate and bolts tighten. For sure I will be free of leaking............I hope..................................Regards Quote Link to comment Share on other sites More sharing options...
Andydodge Posted November 12, 2017 Report Share Posted November 12, 2017 Fernando, thanks for posting the pic showing the fibre washer that I mentioned in my post in this thread.........this is one reason why I would suggest gettinga newly made water pump as they have a sealed bearing but are obviously a more expensive proposition than just a rebuild kit but its a personal choice..............andyd Quote Link to comment Share on other sites More sharing options...
Thomba48 Posted November 21, 2017 Report Share Posted November 21, 2017 On 13.10.2017 at 3:12 PM, knuckleharley said: Yes. You can trust the factory shop manual and Motors Automobile Repair Manuals. If they tell you something is that simple,it is that simple. My only additional suggestions would be to tape a piece of cardboard cut to the size of the radiator core to the radiator to keep from accidentally damaging any fins accidentally, as well as to save the skin on your hands. Old radiator cores are nasty things,and they create nasty,infected cuts that make your hands sore. The next thing to do is remove the fan before you loosen the fan belt or do anything else. Putting the fan back on should be the next to last thing you do,and removing the cardboard should be the last thing you do. Don't ask me how I know this. Why can't one leave the fan attached to the water pump section and than take everything out together? :-) Quote Link to comment Share on other sites More sharing options...
knuckleharley Posted November 21, 2017 Report Share Posted November 21, 2017 9 minutes ago, Thomba48 said: Why can't one leave the fan attached to the water pump section and than take everything out together? :-) You can,but it seems to me to be simpler and safer to remove the fan blade first because doing that reduces the chance of chewing up the radiator core with the fan blades when you take the pump off. Quote Link to comment Share on other sites More sharing options...
Thomba48 Posted November 21, 2017 Report Share Posted November 21, 2017 Just now, knuckleharley said: You can,but it seems to me to be simpler and safer to remove the fan blade first because doing that reduces the chance of chewing up the radiator core with the fan blades when you take the pump off. OK thanks Quote Link to comment Share on other sites More sharing options...
DJ194950 Posted November 21, 2017 Report Share Posted November 21, 2017 If you feel that there is room and three people to do the job, go for it without fan/water pump removal. Must turn the fan as it come out to clear the lower outlet on the radiator-per my old memory. It is your car do as you choose! DJ Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.