52cranbrook4 Posted July 27, 2017 Report Share Posted July 27, 2017 On 1/29/2015 at 5:38 AM, Robert Horne said: I am using a 1995 Ford Ranger rearend, 58.50 wide, 3.73 gear, drum type. Had to add 1 inch spacers to get the tire out to where I wanted them. The Explorer would be a better fit in my Coupe. I believe my Jeep rear, 60 inch wide, will be the best fit with my 70's wheels. Did the drive shaft bolt right up to the ranger rear end? Quote Link to comment Share on other sites More sharing options...
50 coupe Posted July 28, 2017 Report Share Posted July 28, 2017 18 hours ago, 52cranbrook4 said: Did the drive shaft bolt right up to the ranger rear end? Using Explorer rear end on my '50 coupe it did not. I made a 'coupler' but eventually had a proper driveshaft made. It was less than $300 and well worth it. Quote Link to comment Share on other sites More sharing options...
Robert Horne Posted July 29, 2017 Report Share Posted July 29, 2017 On 7/27/2017 at 2:24 PM, 52cranbrook4 said: Did the drive shaft bolt right up to the ranger rear end? Yes, I used an Explorer driveshaft, that bolted to the Ranger rear, working great... Quote Link to comment Share on other sites More sharing options...
52cranbrook4 Posted July 31, 2017 Report Share Posted July 31, 2017 On 7/28/2017 at 8:19 PM, Robert Horne said: Yes, I used an Explorer driveshaft, that bolted to the Ranger rear, working great... So what did you do for the transmission side of the driveshaft? Quote Link to comment Share on other sites More sharing options...
48ply1stcar Posted July 31, 2017 Author Report Share Posted July 31, 2017 I think this is what your looking for. 3 Quote Link to comment Share on other sites More sharing options...
Robert Horne Posted August 2, 2017 Report Share Posted August 2, 2017 On 7/30/2017 at 8:30 PM, 52cranbrook4 said: So what did you do for the transmission side of the driveshaft? This is when I installed the TK5 Ranger trans... Ranger trans, Explorer driveshaft, Ranger rearend.. 2 Quote Link to comment Share on other sites More sharing options...
Xlarashun Posted August 2, 2017 Report Share Posted August 2, 2017 My Dad and Granddad used to make those in the mid-fifties for the Mopar dealerships, because, they were ripping the drive shafts out of them on the showroom floor! Quote Link to comment Share on other sites More sharing options...
Plymouthy Adams Posted August 2, 2017 Report Share Posted August 2, 2017 5 hours ago, Xlarashun said: My Dad and Granddad used to make those in the mid-fifties for the Mopar dealerships, because, they were ripping the drive shafts out of them on the showroom floor! are you referring to the rear axle getting ripped out or the ball and trunion style joint...Mopar continued the ball and trunion I know through '65 connecting some pretty serious HP to them as they saw service with the B engines..... 1 Quote Link to comment Share on other sites More sharing options...
MackTheFinger Posted August 2, 2017 Report Share Posted August 2, 2017 (edited) I bought a 5 bolt Dakota rearend from Falconvan for my '47 Plymouth but haven't gotten around to installing it yet. I believe the Dakota has somewhere around 3.55 gears. He relocated the spring perches and rebuilt the rearend but ended up using an Explorer rear. My car has already had the u-joint conversion completed so it should be an easy swap. The original rear is working fine, brakes are good, etc. so it's not a priority. I'll post results when I finally get around to changing it. That's my 100th post!! I'm getting way too gabby!! Edited August 2, 2017 by MackTheFinger 2 Quote Link to comment Share on other sites More sharing options...
Xlarashun Posted August 3, 2017 Report Share Posted August 3, 2017 Dad told me that they were at one of the dealerships picking up two new shop pickups, and a salesman managed to toss the drive shaft out of a brand new '57 Imperial with a prospective customer in it! Dad told them that they could fix the problem! They went to the shop on Monday, and built ten replacement shafts for them by wednesday! Quote Link to comment Share on other sites More sharing options...
Kiwicranbrook Posted August 4, 2017 Report Share Posted August 4, 2017 I'm looking at using a Cherokee rear end in my 52, are the 4x4 diffs ok to use? We didn't get many 2wd Cherokee in NZ Quote Link to comment Share on other sites More sharing options...
wayfarer Posted August 6, 2017 Report Share Posted August 6, 2017 The 4x4 unit will work. You will still be moving the spring perch with either unit. 1 Quote Link to comment Share on other sites More sharing options...
belvedere666 Posted August 6, 2017 Report Share Posted August 6, 2017 On 7/31/2017 at 4:29 AM, 48ply1stcar said: I think this is what your looking for. would this work with the or original trans, explorer drive shaft and rear end without having to lengthen or shorten the drive shaft? Quote Link to comment Share on other sites More sharing options...
wayfarer Posted August 7, 2017 Report Share Posted August 7, 2017 The Explorer assembly already has a flange on each end. IDK if the bolt pattern is the same as the old Mopar. Mixing parts and brands that are 60 years apart generally requires some fab work. Only when you have the rear axle installed will you actually know what the new driveshaft length will be. OK, if you find some who has done the exact same swap then you could use their dimensions but, it would probably be faster to do the swap than to search for that 'one' person. 1 Quote Link to comment Share on other sites More sharing options...
Adam H P15 D30 Posted August 7, 2017 Report Share Posted August 7, 2017 (edited) 1 hour ago, wayfarer said: The Explorer assembly already has a flange on each end. IDK if the bolt pattern is the same as the old Mopar. Mixing parts and brands that are 60 years apart generally requires some fab work. Only when you have the rear axle installed will you actually know what the new driveshaft length will be. OK, if you find some who has done the exact same swap then you could use their dimensions but, it would probably be faster to do the swap than to search for that 'one' person. Just to answer the above question: Neither the flange from an 8.8 or the 7.5 Ford axle is the same as the one needed to bolt to our transmissions.... I have them both sitting on my shelf and the bolt circles are too large. Adam On edit: When I installed the Ford 8" in my 49 Dodge Wayfarer, the new driveshaft was an overall length of 59 inches. Your results may vary but you have an idea on the length needed. + or - and inch or 2. I don't think the Explorer driveshafts are that long, but I have never measured one. Edited August 7, 2017 by Adam H P15 D30 1 Quote Link to comment Share on other sites More sharing options...
dndrodshop Posted September 3, 2017 Report Share Posted September 3, 2017 I used a Mopar "E" Body 8-3/4" Rear that bolted to the stock springs without modification. I did stack the stock u-bolt /shock mount plate between the 8-3/4 u-bolt plate and the rear end or the shock mounting. Been running it since 1989. 1 1 Quote Link to comment Share on other sites More sharing options...
Dartgame Posted September 5, 2017 Report Share Posted September 5, 2017 dnd - which car did you put the Ebody axle in ? I recall E body axles are pretty wide- any issues with tire clearance ? Quote Link to comment Share on other sites More sharing options...
dndrodshop Posted September 27, 2017 Report Share Posted September 27, 2017 Late answer to you question - 48 Plymouth Sedan, 440 power, Yea you do have some limitations on tire size, I think a 235 is about as wide as you can get with stock frame rails and fenders. Quote Link to comment Share on other sites More sharing options...
Randy Curran Posted October 2, 2017 Report Share Posted October 2, 2017 I used a '79 Nova 10 bolt. Just moved the perches. I have dual bolt pattern wheels so no biggie there. I know it's a Chevy part but the engine (SBC) and rear axle were free and I'm broke so... Quote Link to comment Share on other sites More sharing options...
Cudan Posted October 2, 2017 Report Share Posted October 2, 2017 2 hours ago, Randy Curran said: I used a '79 Nova 10 bolt. Just moved the perches. I have dual bolt pattern wheels so no biggie there. I know it's a Chevy part but the engine (SBC) and rear axle were free and I'm broke so... hi , is this the same axle as a second generation camaro ? ( i also have a sbc in the corner off the garage ) Quote Link to comment Share on other sites More sharing options...
Randy Curran Posted October 2, 2017 Report Share Posted October 2, 2017 I believe so. And free is good!!!! Quote Link to comment Share on other sites More sharing options...
Robert Horne Posted October 3, 2017 Report Share Posted October 3, 2017 On 8/7/2017 at 10:33 AM, wayfarer said: The Explorer assembly already has a flange on each end. IDK if the bolt pattern is the same as the old Mopar. Mixing parts and brands that are 60 years apart generally requires some fab work. Only when you have the rear axle installed will you actually know what the new driveshaft length will be. OK, if you find some who has done the exact same swap then you could use their dimensions but, it would probably be faster to do the swap than to search for that 'one' person. When I installed my 5 speed Ranger trans, I made an temp adapter to fit a temp driveshaft, to fit on my Plymouth rearend, Worked ok. I later changed to a Ranger rear, with a Explorer driveshaft.. 1 1 Quote Link to comment Share on other sites More sharing options...
ACJCF2 Posted October 3, 2017 Report Share Posted October 3, 2017 This has been a great thread and a huge source of information. I picked up a 94-95 Jeep Cherokee rear end for my 49 Coronet. I believe it to be a 3.55. Quote Link to comment Share on other sites More sharing options...
Robert Horne Posted October 4, 2017 Report Share Posted October 4, 2017 On 10/2/2017 at 11:50 PM, ACJCF2 said: This has been a great thread and a huge source of information. I picked up a 94-95 Jeep Cherokee rear end for my 49 Coronet. I believe it to be a 3.55. My 98 XJ Jeep 2 wheel drive has a 3.55 rear, looks to be a good fit for my 37 or 38 Coupe..... Quote Link to comment Share on other sites More sharing options...
Dartgame Posted October 5, 2017 Report Share Posted October 5, 2017 Does anyone know how to decipher the mopar codes for jeeps relative to the axle ratio and open vs limited slip ? Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.