Jump to content

The Oil Soup

Members
 View Profile  See their activity

  • Posts

    651

  • Joined

  • Last visited

  • Days Won

    2

 Content Type 

Everything posted by The Oil Soup

  1. The Oil Soup
    . That looks how guys from Nevada handle dopey drivers
  2. The Oil Soup
    Would it be impractical to run the fuel line over the transmission and down the passenger side to the fuel pump? Has anyone done this?
  3. The Oil Soup
    Give me a P, give me an A, give me a T, give me an I, give me an N, uh Alex I'd like to buy a vowel, give me an A. What's that spell?
  4. The Oil Soup
    The crease would show where it wraps around the side and I believe the bed is the same from the pre '48 trucks.
  5. The Oil Soup
    Cool milk truck!
  6. The Oil Soup
    I think the photo or truck has been modified/altered. There is no vent window on the drivers door but one on the passenger side, the shading shows the roll of the sheet metal under the rear window but not on the body line, also a slight line at the lower cab indents may be a scratch or fold on the photo. The light source and clarity of the images of the children seems inconsistent. More photos?
  7. The Oil Soup
    Except for the windshield all my glass is tempered. You have plenty of options with colors.
  8. The Oil Soup
    On my Steele gasket the holes lined up fine.
  9. The Oil Soup
    You can get tubas made from brass also, but don't confuse the two.
  10. The Oil Soup
    I used them on the rear axle on mine. I believe they are 2.75" on center vs 4" for the stock ones. Worked fine for me. Lowered the ride height less than 1"
  11. The Oil Soup
    You might check your rings, I don't think it's supposed to smoke like that.
  12. The Oil Soup
    I found a carter inline glass bowl filter on ebay
  13. The Oil Soup
    A shop that rebuilds alternators or generators can take care of the starter
  14. The Oil Soup
    I put the fuzzy strip on both sides of the window instead of using the rubber bumpers and then installed the glass but that is w/o vent windows. may be different with them.
  15. The Oil Soup
    I did mine a while ago and I think that's right, disconnect rollers in track, rotate window 90 degrees, remove through top of door, remove regulator through access panel. Also w/o vent windows.
  16. The Oil Soup
    Can't wait until you're retire'd!
  17. The Oil Soup
    How about photos of the tach Paul?
  18. The Oil Soup
    Nice Paul!
  19. The Oil Soup
    Can't wait to see that hood ornament!
  20. The Oil Soup
    Go to http://www.crlaurence.com/crlapps/showline/offerpage.aspx?Productid=3300&GroupID=1677&History=39324:1497:1507&ModelID=1677 Type 720 into search for glass setting tape. 1/16" should be the right size. Use window cleaner as a lubricant on the glass and on the rail. Rail can be crimped slightly before install if it seems loose on glass. Rubber side of tape goes toward glass, cloth side toward rail. Good luck, Gary
  21. The Oil Soup
    At this point I won't be pulling the bearing caps. Thanks
  22. The Oil Soup
    Can anyone give me some help as to what these are and how they install on the motor. I dropped the oil pan because I wasn't getting oil pressure, cleaned out the sludge, reinstalled oil pan. I am now getting oil pressure when I crank the motor. Checked the manual but don't see a reference for these. B4B 218 Thanks
  23. The Oil Soup
    Here is a chart that should help . http://www.moog-suspension-parts.com/Universal_Outer_Tie_Rod_Ends.asp
  24. The Oil Soup
    That looks like it ought to be on Paul's truck.
  25. The Oil Soup
    Under 6' on my B4B
×
×
  • Create New...

Important Information

We have placed cookies on your device to help make this website better. You can adjust your cookie settings, otherwise we'll assume you're okay to continue.

Terms of Use