DJ194950

This is in Ca. No pictures at this time, just heard about this. Just asked by my neighbors good friend if a $17.5k price was within reason. I did not think so. My quick opinion only.(best, but lousy guess). Supposedly very nice condition, newer flat 6, no known rust after top side and rocker panel condition inspection by the friend. show topside, nice driver condition as seen/ridden in. Opinions as to reasonable price?? I suggested 12K in $100 bills --after on rack inspection. High or low?? DJ

Branded, did you notice that the speedway runtz resistor says for negative ground only? Just in case if that polarity change is Not make- just pointing that out for info. DJ

Can anyone picture Paul flying over the dunes while throwing sand everywhere on the sand dunes with those paddle tires of Pismo Beach Ca.??

Signed, D. I'm in trouble now, back to the corner of the garage I go! DJ

Did Mopar ever have a R-11?? Have seen lots of Ford r-11's on ebay but the input shaft and mount pattern are not the same as Mopar. If your current 3 spd. is side shift type and of the same type syncho's (pin or brass spider type, later years or early) the parts can be interchanged with the R-10 except for the main shaft. If your into the job, taking the OD housing and parts off to inspect them for damage you may be able to just rebuild the 3 spd. part if the OD section parts are good! Input shaft, rear output shaft etc. bearings and seals are available from local bearing supply houses. Other parts are not hard to find Except the OD pieces can be Very hard to get. I believe rebuild instruction are avail. on this forum in the downloads section located at the header of this forum. Probably I would get the truck up and running, drive through the summer as is and inspect the OD parts of the R-10 which will really give you a choice at that point. Very nice truck and on your hemi work! DJ

I Need a definite answer on the "swirl" question! Please! I had many people ask me if it was true- I had no answer for them as I did not ever pay any attention in the 8 months I spent there many years ago. One person got MAD at me for not assuring him that it was true! DJ

Fuel pump arm springs from 2 pumps that came apart?? DJ

On many "new type fuel senders one pole is for a separate ground wire as to not count on the tank itself to be grounded. Usually they are marked on the sender. If not make sure both poles are insulated from the mounting plate and use either one as a ground terminal makes no difference as the sender is just a variable resistor to ground. Run a separate ground to be body close by. DJ

Will never get pedal pressure if all the drums are not all installed or tie down straps wrapped tightly around all the shoes. if the shoes can expand much the air cannot be released. DJ

Choke?? DJ

Maybe a grease needle will work? Amazon.com Lumax LX-1415 Silver 3-5_8' Needle-Type Adapter Automotive.html

Thanks for the response Dr. I will share this with him and hopefully answer all his questions at once. The comparison pictures close together really show the differences. DJ

Possibly the frame is twisted? Long shot, but measurements could tell you or sure with suspension parts out of the equation if frame to leveled side to side and front to back on a good flat surface. ?? DJ

If it can be done to Furd model a's and t's, sure do not see why not. Finding the bearings with the correct dimensions may be the issue?? DJ

The owner of this 47 Ply. bus. cpe in my garage (a good friend) keeps asking what is the difference between a bus. cpe. and the club cpe. Some pictures for his comparison Dr would possibly answer his question. Pictures please! Thanks for your response. DJ for Ken.

Hang a line and clean you underwear at the same time! Make your wife happy also! DJ

Are you sure you we reading PSI? Maybe Kpa where 125 is about 18 Psi? Is not 125 almost at the top of Max? Sounds like your new truck engine to me! DJ.

The new owner of Mary's 47 has a gallon at least for free also. Shipping only cost. ($45.00 value) Almost enough for the change with both over-minus their recommended flush solution! Anyone e;else what to what to donate? DJ

Ya looking for a new project Paul ? May know of a short wheelbase Dodge flathead 6 with flatbed in Modesto area! Make your own cab-over? DJ

Seems some like to piss in other Wheaties! Stock steering clearance? Trans mount? Can he weld or have others do it? Here is a motor mount kit, trans mount kit to fit with 1" passenger offset for $300. http://www.butchscoolstuff.com/eng-trans-mounting-kits-4/ DJ

A search for- tappet wrenches for sale-canada got some responses like this one, https://www.acklandsgrainger.com/en/category/Open-End-Wrench-Sets/Wrenches/c/26853 DJ

Temporary cat hotel or full time? They only need a cubicle! No matches allowed! DJ

Key word-lived with? Sorry to get maybe out of bounds with this post? To be honest-never worked out good for me.

Some bed/under coating can be mixed with color pigments to match the car color. Consult your local paint store about the possibilities. Just a slightly different/mix/match of ideas? DJ

Well it may be a ________, but i am sure you can noise with the best!! DJ