chris 48 P15 Posted July 25, 2022 Report Posted July 25, 2022 refaced flywheel new clutch disk and pressure plate installed with clutch pedal pressed down and trans in 1st gear when i let of the clutch pedal car stutters and jumps only from standstill when moving goes int other gears smooth even into first Quote
plymouthcranbrook Posted July 26, 2022 Report Posted July 26, 2022 (edited) Did you make sure everything was tightened correctly and evenly? Any possibility of grease or oil getting on the disk or pressure plate? Make sure your transmission and engine mounts are tight and in good shape. And be sure the clutch linkage is not bent or out of alignment. And did you replace the throwout bearing? Edited July 26, 2022 by plymouthcranbrook Quote
chris 48 P15 Posted July 26, 2022 Author Report Posted July 26, 2022 tightened everything correct and even no oil or grease will look over mounts what is clutch linkage replaced throw-out bearing thinking of doing it over again to check my work Quote
plymouthcranbrook Posted July 26, 2022 Report Posted July 26, 2022 Clutch linkage is the connection from the floor pedal to the clutch fork. Make sure it is connected all through and moves easily and smoothly. Manual should show it. Quote
MarcDeSoto Posted July 26, 2022 Report Posted July 26, 2022 Here's a blow up of the clutch linkage from the Parts Manual. 1 Quote
chris 48 P15 Posted July 26, 2022 Author Report Posted July 26, 2022 the linkages are loose i will look to see if i can adjust or tighten Quote
1949 Wraith Posted July 26, 2022 Report Posted July 26, 2022 Are your universal joints in good condition? Quote
chris 48 P15 Posted July 26, 2022 Author Report Posted July 26, 2022 the universal joints are the ball and trunnion type seemed to turn freely no binding or play i have read the stories with these type of u joints so i dont ant to take it apart yet one problem at a time i think it may be the linkages or a mistake on the assembly Quote
chris 48 P15 Posted July 26, 2022 Author Report Posted July 26, 2022 ordered the clutch shaft pivot bearing will replace and see if solves problem Quote
amishguy Posted July 26, 2022 Report Posted July 26, 2022 I had a turned flywheel warp on me once it took me forever to figure that out. put a run out gauge on clutch surface and was 40 thousands out of wack grabbed like mad Quote
oldodge41 Posted July 27, 2022 Report Posted July 27, 2022 Worn out bushings on the rear leaf spring shackles can and will cause a car to "chatter" upon clutch engagement as well. Quote
chris 48 P15 Posted August 1, 2022 Author Report Posted August 1, 2022 update took the clutch apart again found errors on my part i didn't tighten pressure plate properly changed the engine mounts will also change the clutch torque shaft bearings waiting for helper to button up for test drive Quote
busycoupe Posted August 1, 2022 Report Posted August 1, 2022 Replacing the motor mounts can cause the shift linkage to bind or not work. If you are having trouble with shifting on your maiden voyage check the shift rod adjustments. Quote
Booger Posted August 1, 2022 Report Posted August 1, 2022 On 7/26/2022 at 2:17 PM, chris 48 P15 said: ordered the clutch shaft pivot bearing will replace and see if solves problem If thats what were calling a throw out bearing I bet thats the problemo Quote
chris 48 P15 Posted August 2, 2022 Author Report Posted August 2, 2022 2 different parts a throw out bearing is not a pivot shaft bearing no problem oh Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.