White Spyder Posted June 8, 2021 Report Posted June 8, 2021 (edited) 48 Chrysler with a 251 six cylinder engine. Had to remove the oil canister and lines to replace a leaking Welch plug. Decided to clean the lines and canister before reinstalling. Water washing things up I found a copper crush washer in the tub. Looking further, I found what appears to be another in the bottom inlet on the canister. Still have to take a scraper to it. With flared metal lines, are there supposed to be crush washers on the lines going to the canister? If so, what about the lines going to the block? Thanks, Edited June 8, 2021 by White Spyder Add Quote
TodFitch Posted June 8, 2021 Report Posted June 8, 2021 Flare and double flare fittings should not need crush washers. I wonder if the elbow in your photo is damaged and that was some PO's attempt at a fix. Quote
Plymouthy Adams Posted June 8, 2021 Report Posted June 8, 2021 (edited) I agree with Tod...that is something I do not recall seeing....but...I am still a young guy.....? Edited June 8, 2021 by Plymouthy Adams Quote
desoto1939 Posted June 8, 2021 Report Posted June 8, 2021 The two fittings that come out of the oil filter canister should be a flare fitting and the oil lines should also be a flared fitting and I would think that they are double flared. The lines were leaking so the prior owner did a quick fix. Rich Hartung desoto1939@aol.com Quote
Tooljunkie Posted June 9, 2021 Report Posted June 9, 2021 There are copper washers that are used to aid with sealing inverted flare lines. Not that i have ever used them, but i just saw a thread about them in another forum. McMaster carr or Grainger sells them. Quote
Plymouthy Adams Posted June 9, 2021 Report Posted June 9, 2021 (edited) Live and learn...had no idea there were Band-Aids for flare fittings....why am I surprised......snake oil and magic bullets for everything else why not this... Edited June 9, 2021 by Plymouthy Adams 1 Quote
TodFitch Posted June 9, 2021 Report Posted June 9, 2021 4 hours ago, Plymouthy Adams said: Live and learn...had no idea there were Band-Aids for flare fittings....why am I surprised......snake oil and magic bullets for everything else why not this... Me neither. Learned something new today. But I think I’d still replace any fitting that wasn’t sealing properly rather than putting a crush washer in the old one. Quote
Plymouthy Adams Posted June 9, 2021 Report Posted June 9, 2021 you and I both.....sometimes cheap and easy is cheap and sleasy Quote
Tooljunkie Posted June 9, 2021 Report Posted June 9, 2021 I would still make a new line or replace fitting. Typically i treat every inverted flare like it was for brakes,safety being important to me. Quote
White Spyder Posted June 9, 2021 Author Report Posted June 9, 2021 4 hours ago, Tooljunkie said: I would still make a new line or replace fitting. Typically i treat every inverted flare like it was for brakes,safety being important to me. I think so too but what if it is the canister side that ie the problem? Won’t know until it is re-installed and filled. The lines were a pia to get off and I would not want to damage the canister. Quote
Dodgeb4ya Posted June 9, 2021 Report Posted June 9, 2021 Those special copper crush washers like can be found at McMaster Carr are fairly common. Those cupped copper sealing washers are correct factory installed parts on the Chrysler six to be sure of no leaks on the 1/2" steel oil filter lines. Trying to make those 1/2" steel oil filter lines like the factory would be extremely difficult....wouldn't try it. They don't ever fail unless damaged by physical damage. I have used those same cupped copper washers when installing the 5/8" AC lines on a 60 Imperial. They come in several sizes. Quote
Plymouthy Adams Posted June 9, 2021 Report Posted June 9, 2021 (edited) thanks.....I have never worked on the 'older' larger lines as you describe...thus I have not been exposed to these...I would guess this the why for the AN fittings...have only retrofitted newer AC into the older cars....not repaired a 50's AC that I can remember. Edited June 9, 2021 by Plymouthy Adams Quote
White Spyder Posted June 10, 2021 Author Report Posted June 10, 2021 (edited) 21 hours ago, Dodgeb4ya said: Those special copper crush washers like can be found at McMaster Carr are fairly common. Those cupped copper sealing washers are correct factory installed parts on the Chrysler six to be sure of no leaks on the 1/2" steel oil filter lines. Trying to make those 1/2" steel oil filter lines like the factory would be extremely difficult....wouldn't try it. They don't ever fail unless damaged by physical damage. I have used those same cupped copper washers when installing the 5/8" AC lines on a 60 Imperial. They come in several sizes. Where do you get them? Andy B. Doesn’t have them nor even knew about them? What about where they go into the block? I didn’t see any there. Maybe they fell off befor I saw them. I was working at an odd angle with a crows foot to brake the nuts loose. Edited June 10, 2021 by White Spyder Quote
Dodgeb4ya Posted June 10, 2021 Report Posted June 10, 2021 Those special washers are called a copper 45 degree flare gasket or washer. NAPA used to sell them for doing AC line /hose end fittings. "Parker" also had them. Pretty sure the 46-48 Chrysler parts book lists those copper washer with the part# too. The fittings into the block are pipe thread...no additional sealing needed except thread sealer. The copper washers fit into the recess where the tube nut screws down into the fittings. The steel tube nut crushes the steel tube onto the 45 degree flared thin copper washer for leak free seal. Those flared 45 degree copper washers are narrow,thin and of soft. Quote
White Spyder Posted June 11, 2021 Author Report Posted June 11, 2021 Ordered them through Grainger. Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.