47Nik Posted April 6, 2020 Report Share Posted April 6, 2020 I am ready to get new rims and tires for my 47. I want to use the original hub caps if possible. I also want to spend minimal on the wheels since it's just a driver and nothing fancy. Was either gonna weld clips on some existing rims, but worried about them being out of balance then. Any ideas ?? Thanks, Nik Quote Link to comment Share on other sites More sharing options...
Plymouthy Adams Posted April 6, 2020 Report Share Posted April 6, 2020 later mopar rim of the 70's had the extra set of holes between mounting holes that may alloy you to attach clips....this is just a maybe....else look for a set of originals wheels and be sure you getting a solid set for your money and time to process them. You have few options with original poverty caps... Quote Link to comment Share on other sites More sharing options...
58prostreet Posted April 6, 2020 Report Share Posted April 6, 2020 I got some clips from Chevs of the 40"s. I used them to replace some missing original clips and they worked fine. Go to wheels, then hub caps. I used small bolt and lock nut, but could probably weld also. e Quote Link to comment Share on other sites More sharing options...
dpollo Posted April 6, 2020 Report Share Posted April 6, 2020 use wheels from a Desoto or Chrysler Royal or Windsor 48 to 54 or Dodge, but you must have a matched set (different offset (except Canada) Quote Link to comment Share on other sites More sharing options...
Sniper Posted April 7, 2020 Report Share Posted April 7, 2020 4 hours ago, 58prostreet said: I got some clips from Chevs of the 40"s. I used them to replace some missing original clips and they worked fine. Go to wheels, then hub caps. I used small bolt and lock nut, but could probably weld also. e Are these it? https://www.chevsofthe40s.com/detail/7575/Chevrolet_Hub_Cap_Retaining_Clip.html Quote Link to comment Share on other sites More sharing options...
minicooper Posted April 7, 2020 Report Share Posted April 7, 2020 Detroitsteelwheels.com or mobsteel.com sells clips (they look real close to the originals on my old wheels), I believe the wheels are to be drilled and tapped for these, but I suppose you could tack weld or rivet them on. I put new 16” wheels on my 52 and bought clips from mobsteel.com, for the original caps, but never got around to installing them, purchasing new snap on dishes instead. They were $10.00 a wheel, 5 count. Quote Link to comment Share on other sites More sharing options...
58prostreet Posted April 7, 2020 Report Share Posted April 7, 2020 Yes, those are clips I got from chevs of the 40"s. Quote Link to comment Share on other sites More sharing options...
falconvan Posted April 7, 2020 Report Share Posted April 7, 2020 I’m wondering if you could take the center section from a stock wheel and weld it into a wider hoop? Quote Link to comment Share on other sites More sharing options...
Plymouthy Adams Posted April 7, 2020 Report Share Posted April 7, 2020 I believe some do this and other split the rim, weld in a section and true it back up which really alters offsets....all this is relatively expensive over purchasing wheels already made to X size...while the focus of this thread is using original caps and installing the clips to modern....modern wheels can easily be purchased but the trend starting in the 90's (some earlier) were really positive offsets as the bearing systems changed design at this time in the front hubs. Anyone seeking replacement wheels for these old cars will probably benefit from searching more for 89 and older mopar rear wheel drive wheels. These wheels have a slight positive offset also and often will need 1/4 to 3/8 spacer on the front when fitted with radials due to bulge may contact steering components. Some wheels have these additional 5 smaller holes already in place for attaching specialty caps of the era and will probably support the clips but you may need to be creative here to some degree Quote Link to comment Share on other sites More sharing options...
Ernie Baily Posted April 7, 2020 Report Share Posted April 7, 2020 Hello, When I bought my 48 Plymouth the former owner he took off the 15" wheels and used the on a running 47 Plymouth. I came along and bought the car with the 47 16" wheels. I wanted the car to be correct so I located a 1950 Plymouth in a junkyard and bought all 4 wheels off of the 50( they had the clips to allow the use of the original 48 Plymouth hub caps). I then bought a set of Goodyear collector tires(6:70 x 15) from Jim Benjaminson (benji@utma.com) which he advertises in the Plymouth Owners Club Bulletion. I have my third set on now after 38yrs of ownership. Good Luck and enjoy! Ernie Baily Quote Link to comment Share on other sites More sharing options...
47Nik Posted April 8, 2020 Author Report Share Posted April 8, 2020 Thanks for all the ideas. I'm gonna try to weld or bolt some clips on the wheels I have. I also noticed the 3 hub caps I have are the same diameter, the 3rd one is smaller. Might need to trade for one, I'll try to post some pics. Nik Quote Link to comment Share on other sites More sharing options...
Plymouthy Adams Posted April 8, 2020 Report Share Posted April 8, 2020 there are 9" and 10" caps in the poverty lineup....however the opening that is the retainer clip circle is the same on both... Quote Link to comment Share on other sites More sharing options...
Bob Riding Posted April 8, 2020 Report Share Posted April 8, 2020 Something to consider: when I was looking for 16" stock wheels for the '40 wagon, I had numerous parts cars on the property and took 17 wheels down to my cousin's wheel alignment shop to be checked for true. Of the 17, 4 were acceptable, the rest were bent or so out of true as to be unusable. Not sure how much effort it takes to true up a wheel (without the tire), or how you would do it, so a modern alternative where you added the clips might be the path of least resistance. Quote Link to comment Share on other sites More sharing options...
47Nik Posted April 8, 2020 Author Report Share Posted April 8, 2020 I see, never heard them called poverty caps, lol. Quote Link to comment Share on other sites More sharing options...
Plymouthy Adams Posted April 8, 2020 Report Share Posted April 8, 2020 stick around, you subject to hear a lot more before its all over......and another note...the 10's are needed if you choose to run the optional dressing ring be it stainless or painted as the extra skin will hide the parting line and cover these for dress and retention. Quote Link to comment Share on other sites More sharing options...
47Nik Posted April 8, 2020 Author Report Share Posted April 8, 2020 Glad to know, well I have 3 10" caps need 1 more. Does anyone need a 9 incher ? Quote Link to comment Share on other sites More sharing options...
47Nik Posted April 9, 2020 Author Report Share Posted April 9, 2020 Here's the current rims, not sure what there off of. Quote Link to comment Share on other sites More sharing options...
junkers72 Posted April 9, 2020 Report Share Posted April 9, 2020 Look like 1955-56 . 1957 went to 14” Quote Link to comment Share on other sites More sharing options...
MarkAubuchon Posted April 9, 2020 Report Share Posted April 9, 2020 I too have had a heck of time finding true 16" wheels, finally switched to 15 " originals but even that was a challenge to find 4 straight ones. On my current project Im buying brand new steel wheels and adding the clips. Need to remember this was never much of problem for the era when most of the roads where gravel and dirt. Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.