Jump to content

Gasoline.


48P15Annie

Recommended Posts

Regular unleaded also, plenty enough octane.

E-10 so far in Manitoba, I have an all new fuel system, new ank lines etc, so no issues.

Our premium, has no ethanol, some use that for older engines etc........

Link to comment
Share on other sites

The engines come with hardened valve seats so they do not need the lead to prevent the hot spot weld of the seat and the valve. When I rebuilt mine I used Chevy stainless steal exhaust valves in my engine and all that I run is regular and mine is bored .040 over and the head was milled .100 also. I have had no problems with the valves and I run mine pretty hard, cruise at 70 MPH on the highway, I try to keep it below 3600 RPM most of the time.

Link to comment
Share on other sites

I use the lowest octane gas available. If I read the literature correctly my 1933 engine's 5.5:1 compression ratio should be fine down to about 70 octane. And it has the hardened exhaust valve seats so it does not need leaded fuel.

I did have some issues with hot start "vapor lock" for the first time this last summer. Only happened on the hottest days (95 degrees) after long stints of high speed driving. A bit of water poured on the fuel pump to cool it seems to work around that issue.

Link to comment
Share on other sites

Regular unleaded is fine for a stock '48 Plymouth. However, as premium has more detergents, I use the premium to help keep the fuel system clean. There is also some evidence that premium has a lower tendency to form varnish and other sludge. After driving a '76 Eldo w/ fuel injection for two years, I am very particular about fuel system PM.

As my engine is from a '56 Dodge, there is some disagreement on whether or not the practice of building these engines with hardened valves and seats continued after 1955, I do run lead substitute and lead replacement. If nothing else, the lead helps the valves seal better and there is improved upper cylinder lubrication.

Link to comment
Share on other sites

Can some one please explain to me what there is in the "UPPER CYLINDER" that requires lubrication???? All I can see above the top of the piston at TDC is open space comprised of the cumbustion chamber as defined by that area of the cylinder not swept by the piston and the volume defined by the machined area of the cylinder head. What needs greased???

Link to comment
Share on other sites

Is regular leaded gasolene available for purchase anywhere today?

Not that I want to buy any, I am just curious?

I think our friends south of the Rio Grande may have it still. I remember back in the '80s when intrepid old car driving Texans would drive down to Mexico to fill up on their leaded petrol. However, that was almost 30 years ago, and I haven't been to Mexico myself in almost 20 years.

Link to comment
Share on other sites

Looks like I'm the odd man out again. When we put my flathead together with 9 to 1 compression, my mechanic said that all flatheads with relatively high compression have detonation issues, so I have always run Chevron 91 octane.

Marty

Link to comment
Share on other sites

Looks like I'm the odd man out again. When we put my flathead together with 9 to 1 compression, my mechanic said that all flatheads with relatively high compression have detonation issues, so I have always run Chevron 91 octane.

Marty

With a 9:1 compression ratio I think you will need pretty high octane. I bet the 91 octane you are using is just about as low as you can go.

Link to comment
Share on other sites

Looks like I'm the odd man out again. When we put my flathead together with 9 to 1 compression, my mechanic said that all flatheads with relatively high compression have detonation issues, so I have always run Chevron 91 octane.

Marty

Marty;

You are not the odd man out. You are the one that fully knows the fuel requirements of the engine you built. When you do a compression test what numbers do you get?

Link to comment
Share on other sites

Most people I know no longer go down to Mexico anymore too dangerous, due to all of the drug crime. Too many people killed in the dope trade and among rival gangs. Now Houston has gotten a big gang problem that's tied to the Mexican dope gangs. My brother lives in El Paso and their news is almost all about the killings across the border.

Link to comment
Share on other sites

Most people I know no longer go down to Mexico anymore too dangerous, due to all of the drug crime. Too many people killed in the dope trade and among rival gangs. Now Houston has gotten a big gang problem that's tied to the Mexican dope gangs. My brother lives in El Paso and their news is almost all about the killings across the border.

Even the tourista destinations like Puerta Vallarta, Aculpoco, are getting dangerous.

I still know people that travel by road on there bigger highway from Texas to Puerta Vallarta, I think there crazy in doing so........

Link to comment
Share on other sites

Is regular leaded gasolene available for purchase anywhere today?

Not that I want to buy any, I am just curious?

A few of those people that glared at me, said they buy a lead additive and add it to unleaded gas?

Thanks for the input guys.

Would it be wise to add some carb/fuel injector cleaner to the gas? Or is it too old and could harm something.

Link to comment
Share on other sites

I regularly add Gumout fuel injector cleaner to my 1998 Monte Carlo (3.1 SFI V6). I notice a big difference in performance and mileage. Especially after the first few bottles I ever used it it. The car wasn't well taken care of, and it made it run like a brand new car. Felt like I dropped in a new motor.

Link to comment
Share on other sites

Every time I change oil and any time that I go on a trip over 200 miles, I add fuel system cleaner. A remnant from my time w/ a '76 Eldo and living in Arkansas from 2000-02. Preferred brand for years was STP, but after having used just about every brand known to man (long story about proving a point to a car dealership that probably got out of hand), just a bout any brand will do.

Link to comment
Share on other sites

Below is a site that offers a list of gas stations that still offer un-adulterated (tree huggin' hippie free) gas.

http://pure-gas.org/index.jsp

This list is for ethenol free gas and I found 4 such stations here in my hometown. This old non tree huggin Hippie:D thanks you for posting this linkicon14.gif

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
×
  • Create New...

Important Information

We have placed cookies on your device to help make this website better. You can adjust your cookie settings, otherwise we'll assume you're okay to continue.

Terms of Use