-
Posts
6,072 -
Joined
-
Last visited
-
Days Won
63
Content Type
Links Directory
Profiles
Articles
Forums
Downloads
Store
Gallery
Blogs
Events
Classifieds
Everything posted by RobertKB
-
Pictures always help.
-
I have owned my ‘53 Plymouth since 1975 when it had 68,000+ miles. In all those years it has never left me stranded. I have replaced a few things like fuel pump, water pump, repaired radiator, etc. but the basic mechanicals are original. Transmission and differential have had seals but that’s it. I sometimes think it has quit running when it idles because the engine is so smooth and quiet. As is wise…………I will say “touch wood” to all the above. At some point it will be time to part ways but I would like to own it 50 years which is only two years away.
-
That sounds great! ?
-
My 1953 Canadian Plymouth Belvedere (25” engine, 228 CID) has just over 102,000 miles. It is the original engine with very little work done. In 1977, at 72,000+ miles, I did replace a burnt valve with a good used one and all valves were lapped. As it was kind of apart, I did put new rings in after honing the cylinders. Bearings were plastigauged and were within factory specs so therefore reinstalled. 30,000 miles later the engine still runs great and uses virtually no oil. Serviced and maintained regularly. It just goes to show these old Mopar flatheads run a long time if treated reasonably. So, original pistons, bearings, valves, etc. Only new non-original parts are rings, one valve, and head gasket. P.S. - Paint is original too.
- 6 replies
-
- 11
-
What would you do?? - 52 COE Project
RobertKB replied to 52b3b Joe's topic in Mopar Flathead Truck Forum
You’ll love the concrete floor!? Your best helper is learning young but they grow up so fast that he’ll be driving the COE before you know it!?? -
Clements Tailgate BBQ 16th Annual Event......
RobertKB replied to 48Dodger's topic in Mopar Flathead Truck Forum
When you select the pictures you want to choose your phone should say Show Selected. Hit that and it should then say Actual Size. Hit that and it then brings up size options. Choose one less than 3MB. That’s how my I-Phone works anyway and I almost always use it to post on the forum. Picture below was originally 4.5MB, well above the 3MB allowed, but posted at 664KB. -
Both my ‘53 Plymouth and ‘51 Canadian Dodge have the Detroit joints. The ones in the ‘53 have worked flawlessly for decades although I have replaced the rubber boots with leather. The ones in my ‘51 Dodge have given nothing but trouble. I have a spare driveshaft from a ‘48 Dodge D25 parts car with spicer joints. I also have the appropriate yokes for the transmission and differential. Shaft will need lengthening slightly. Got new u-joints and set to go this spring replacing the ‘51 driveshaft. I don’t mean to hijack this interesting thread but the last few posts might be better in the car forum.
-
I have NEVER understood why GM and Ford stayed with the torque tube so long. Absolutely no advantage to it. Also don’t understand why Mopar stayed with Detroit universal joints for so long. A few of their cars did come with the spicer joint like my 1948 Canadian Dodge D25. Same joint as ‘57 Chev so very easy to find.
-
48 DeSoto engine start up after 40 year ago rebuild
RobertKB replied to MarcDeSoto's topic in P15-D24 Forum
That’s why I’ve always take all manifold nuts and washers, especially the brass ones, off any old Mopar engine that’s only good for parts. I have way more than needed. -
We are dealing with 70+ year old cars here. We should be glad we can even get filters. I know money is important but sometimes you need to “pay to play”.
-
Canadian car. I posted this info from a 1954 Canadian parts manual in a previous post. Check his car’s serial number. His engine serial number starts with D24 so is likely original to the car and according to the car’s serial number would be a 228 CID. It’s always good to read previous posts and look at the information provided.
-
Here’s info on your car from my Canadian parts manual. Most, but not all, Canadian built Dodges were D25’s like mine. Door handles are held in place by two screws behind the handle which on the D25’s are fractionally over 1” long. A specialty bolt that screws into the end of each handle keeps it from being pulled out by someone with bad intentions. D25’s we’re basically Plymouths with Dodge trim. At first glance they look similar but there are lots of differences from the D24’s. Fenders don’t extend into the doors, hood is alligator style not butterfly, rear brake light and taillights are different, etc.
-
That’s a Canadian Dodge D25, aka Plodge. It is a Plymouth with Dodge trim. It will also have the longer 25” engine. If engine is original to the car it will be a 218 CID. Looks like a business coupe. It also looks like it is missing some vertical bars in the grille. I own the club coupe version.
-
ANSWERED Oil Pressure obtained but now have massive leak
RobertKB replied to Marty C's topic in P15-D24 Forum
Gotta love those old fashioned parts stores. We have one where I live but I see it slowly changing after it changed hands. Glad you got the problem sorted! -
Optima battery suddenly too weak to crank on 48 DeSoto!
RobertKB replied to MarcDeSoto's topic in P15-D24 Forum
You have been given this advice by at least four different people, myself included. Have you actually done this? I doubt there’s any need to pull the oil pump. -
Optima battery suddenly too weak to crank on 48 DeSoto!
RobertKB replied to MarcDeSoto's topic in P15-D24 Forum
Lots of discussion on being at TDC on #1 to run the plug wire correctly to the distributor. Gotta make absolutely certain this is on the compression stroke, not the exhaust otherwise you are out 180 degrees on the distributor. Each cylinder only fires every second revolution. It’s an easy mistake to make. Been there, done that many years ago. Also, depending on how the oil pump and distributor are indexed after a rebuild #1 plug wire may or may not be at 7 o’clock. I have one engine where #1 spark plug wire is at 10 o’clock. The engine could care less as long as it’s timed right. -
I own a D25 which is the Canadian 1946-48 Dodge. If the engine is original to the car it is a 218. The engine serial number should also start with D25.
-
Optima battery suddenly too weak to crank on 48 DeSoto!
RobertKB replied to MarcDeSoto's topic in P15-D24 Forum
I still suspect timing. -
Vic's Dodge Gerage closing up shop
RobertKB replied to ggdad1951's topic in Mopar Flathead Truck Forum
People get old. No one to take over. Not enough business. These could be the causes. -
I agree. I had to stop very suddenly in my ‘51 when a semi turned in front of me. Locked up tires and they squawked. Avoid “the old car trap” and go with your plan. Sounds like you might have a slight safety issue you need to deal with. Good luck!
-
I like the third one with buildings nearly the same colour. First one is nice too. I love the fact you use your truck!
-
Of course trucks count!! Anything Mopar! Or parts thereof. ?
-
Definitely not real wood. It is very nice woodgraining though.
-
Yes I painted the wheel. I seem to remember I used Rustoleum RV white which is an off-white and so far has been durable.