51 Fargo Posted February 8, 2009 Report Posted February 8, 2009 This is my first shot at a bumper refit..... My truck had this bumper on it when I got the truck . It is ok but just doesn,t go with the theme of the truck I think So I did a refit with this 49 plymouth Bumper.. Had to cut in Half and stretch it to fit truck I will also be putting a bridge bar in around the Lic Plate to finish it off Quote
buds truck Posted February 8, 2009 Report Posted February 8, 2009 Looks good. I have a Rechrome 50 Dodge Coronet front bumper for mine. It fit without cutting. Got it from a member of the forum on a trade. took a while to find out what it was. Bud Quote
Frank Elder Posted February 8, 2009 Report Posted February 8, 2009 The dodge cars are a wider platform, but you can't go wrong with a ribbed plymouth bumper! It is lookin' good. Quote
Bob_Koch Posted February 9, 2009 Report Posted February 9, 2009 What year plymouth bumper should I look for? Quote
Young Ed Posted February 9, 2009 Report Posted February 9, 2009 Those are kinda in short supply. 49s were a short year due to carry over of the 46-48 design and those bumpers are popular for rods. To the original poster-what did you put in the middle to stretch it? A flat piece for the plate? Quote
51 Fargo Posted February 9, 2009 Author Report Posted February 9, 2009 Those are kinda in short supply. 49s were a short year due to carry over of the 46-48 design and those bumpers are popular for rods. To the original poster-what did you put in the middle to stretch it? A flat piece for the plate? I cut the bumper in half and added 1 5/8 of steel to the center section then made a lic plate bracket to the front side of the bumper. I will be making a bridge bar to fit the bumper that will go around the Lic plate to finish off the bumper Quote
51 Fargo Posted February 10, 2009 Author Report Posted February 10, 2009 I have the rear done whats your input do I keep it full length or cut on black line ??? Quote
pflaming Posted February 10, 2009 Report Posted February 10, 2009 To my taste, I would not shorten the bumper. I think it looks better as a match to the front bumper which is also wrapped around. You might want to paint what you would cut off with a water based paint that would wash off. If you painted the ends black, you might get an idea of how it would look. If you do that, then paint the ends of the front bumpers also to see how they would look if shorter. From a practical point, the longer bumper also protects your fender. There are a lot of short posts in parking lots. Good looking truck! Quote
48Dodger Posted February 10, 2009 Report Posted February 10, 2009 The front bumper seems more flat, with 90 degree turns at the fenders. The rear bumper is rounded without 90's. For some reason my eye wants to see them switched...or....a bumper like the front, on the back. JMHO. Great looking Fargo! 48D Quote
51 Fargo Posted February 10, 2009 Author Report Posted February 10, 2009 Huh Get this both bumper are the same they are 2 fronts and the one on the front of my truck has been cut and tweeked to fit the front of the truck all hiddin behind the lic plate Quote
48Dodger Posted February 10, 2009 Report Posted February 10, 2009 I guess the rear looks to rounded for my eyes....so the front may have been straighten up by the cut behind lic? Maybe the same would be considered for the back, doing like what Bud said. Thx for letting me add my 2 cents. ~48D Quote
woodscavenger Posted February 10, 2009 Report Posted February 10, 2009 Cut the rear and shorten it. It looks great. Where did you get the turn signals? Quote
Dave72dt Posted February 11, 2009 Report Posted February 11, 2009 I'd get the curvature of the back bumper to match the front, section it to bring the ends closer to the bed sides, matching the front's gap, slide the whole bumper forward to match the gap of the front bumper and consider adding a filler panel between the bed and bumper, rear box step plates behind the rear fenders to fill the gap betwen fenders and bumper ends. But that's just me. I like things symmetrical and balanced so they don't look like an add-on. Quote
4852dodge Posted February 11, 2009 Report Posted February 11, 2009 Don't cut either. They look great the way they are. Quote
BobT-47P15 Posted February 16, 2009 Report Posted February 16, 2009 They look good as they are.....would not cut. Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.