MarcDeSoto Posted March 24, 2020 Report Share Posted March 24, 2020 I am trying to find a video that tells me how to fasten new brake lines to the frame of my 48 Desoto. all the how to videos I watched only dealt with how to flare the lines, not how to attach them. Quote Link to comment Share on other sites More sharing options...
Andydodge Posted March 24, 2020 Report Share Posted March 24, 2020 (edited) It depends on whether you want a stock looking setup using 1/4" lines or a more late model setup using 3/16" brake lines........original brake lines were held firm by small sheet metal pieces either bolted onto the frame or spot welded as in the case onto the rear axle.......the end of the metal clamp was bent around the tube holding it firm.......the metal bracket was a rectangular shape about 3/8-7/16th by 1.5" long............if you are not concerned about originality then I'd use "Adel" clamps which originated in the aviation industry and can be obtained in virtualy any size from to hold a 1/8" tube up to 12" or more diameter, 3/16th and 1/4 Adel clamps are common and cheap, they use a metal clamp with a rubber/neoprene sleeve that results in a neat & tidy fixture, admittedly they must be screwed or bolted to the frame but are what most high end hotrods and race cars use..........any good engineering, hot rod, race car or aviation shop should stock them or know where to obtain them or online........just pinched this pic from ebay........andyd Edited March 24, 2020 by Andydodge more info 3 Quote Link to comment Share on other sites More sharing options...
MarcDeSoto Posted March 24, 2020 Author Report Share Posted March 24, 2020 Thank you Andy for that excellent explanation. I assume I can't use the original clamps. I never even knew I could use 3/16" clamps. Would that give more braking power? Marc. Quote Link to comment Share on other sites More sharing options...
Andydodge Posted March 24, 2020 Report Share Posted March 24, 2020 Marc.........if you have the original bolt on clamps theres no reason why you can't reuse them, they as I mentioned generally are held onto the frame by a 3/8 I think SAE/AF headed bolt that has a special type of thread that creates its own thread when screwed into the frame when the lines are attached by the factory.....when undone these bolts leave the thread cut into the hole and so long as you have the little clamp or bracket you just reuse the bolt...........as for whether its a 3/16th or 1/4 size you just use the correct one for whichever size brake line.........its 10.30pm here so I'm not going out to check but am pretty sure the original brake lines are 1/4 tube.......but I could be wrong...........lol............andyd 1 Quote Link to comment Share on other sites More sharing options...
Sam Buchanan Posted March 24, 2020 Report Share Posted March 24, 2020 Original brake lines on my 1948 P15 were 3/16" and that is what I used for the replacements. Quote Link to comment Share on other sites More sharing options...
Dodgeb4ya Posted March 24, 2020 Report Share Posted March 24, 2020 (edited) Later today I'll get you some pics of factory installed 3/16" brake line fasteners. Your car uses 3/16" brake lines. Unless you car is really rusty underneath your factory clips and clamps shoul be easily re-useable. Edited March 26, 2020 by Dodgeb4ya Spelling Quote Link to comment Share on other sites More sharing options...
Dodgeb4ya Posted March 25, 2020 Report Share Posted March 25, 2020 (edited) Jeez....I forgot...will.do it tomorrow? Done....1948 Chrysler brake line clips...same as yours.. Edited March 26, 2020 by Dodgeb4ya Quote Link to comment Share on other sites More sharing options...
Dartgame Posted March 26, 2020 Report Share Posted March 26, 2020 Those spring loaded clamps are available new as they were used on muscle era mopars and probably long after that too. Quote Link to comment Share on other sites More sharing options...
MarcDeSoto Posted March 27, 2020 Author Report Share Posted March 27, 2020 Thanks Dodge, for those pics! Looks easy now! Marc. Quote Link to comment Share on other sites More sharing options...
61farnham Posted March 27, 2020 Report Share Posted March 27, 2020 If your using copper or copper alloy tubing for your brakelines i'd recommend the rubber lined clips as posted above and placing the clips about a foot apart for better support as it's more prone to vibration than the original steel tubing. Quote Link to comment Share on other sites More sharing options...
MarcDeSoto Posted March 28, 2020 Author Report Share Posted March 28, 2020 I'm using the new plastic brake lines. The reason I asked about the clips in the first place is my car was given such a thick undercoating that a lot of stuff is covered up. And the car spent its life in the Palm Springs area, but was undercoated like it was being driven in Michigan. I love having a rust free car now, though! Quote Link to comment Share on other sites More sharing options...
Dodgeb4ya Posted March 28, 2020 Report Share Posted March 28, 2020 (edited) Plastic isn't DOT approved. Except air Brakes Edited March 28, 2020 by Dodgeb4ya Quote Link to comment Share on other sites More sharing options...
Andydodge Posted March 28, 2020 Report Share Posted March 28, 2020 I've never heard of plastic brake lines........where are they from?........andyd Quote Link to comment Share on other sites More sharing options...
61farnham Posted March 28, 2020 Report Share Posted March 28, 2020 (edited) Had to google that, apparently they use nylon brake lines in some light aircraft kits and race cars for weight saving over metal lines, but as Dodgeb4ya states it's NOT for street use. Edited March 28, 2020 by 61farnham Quote Link to comment Share on other sites More sharing options...
Andydodge Posted March 28, 2020 Report Share Posted March 28, 2020 Yeh, I would like to be as sure as winning lotto that the Oz rego depts would allow plastic brake lines..............lol..........andyd Quote Link to comment Share on other sites More sharing options...
Young Ed Posted March 28, 2020 Report Share Posted March 28, 2020 I'm guessing (and hoping) he's actually using the PVC coated steel lines. Quote Link to comment Share on other sites More sharing options...
MarcDeSoto Posted March 29, 2020 Author Report Share Posted March 29, 2020 Yes, I thought they were plastic, but they didn't pass the magnet test. They stuck to my magnet like glue! So Ed is right, they are metal lines coated in a black plastic. But they look like they are 1/4". I didn't know they were supposed to be 3/16. They are kit, with the lines having tags saying what part of the car they go to. Now I forgot where I bought it. I don't have the name of the manufacturer. I wonder if I should try to return these and get 3/16 lines. Does anyone know a good place to buy brake line kits? Quote Link to comment Share on other sites More sharing options...
Sam Buchanan Posted March 29, 2020 Report Share Posted March 29, 2020 They may be 3/16” with an OD of about 1/4”. Quote Link to comment Share on other sites More sharing options...
MarcDeSoto Posted March 29, 2020 Author Report Share Posted March 29, 2020 Oh, you're right Sam. I forgot that 3/16" is smaller than 1/4"! 1/4" is 4/16"! thanks for pointing that out, so I guess I'm good with these lines! Quote Link to comment Share on other sites More sharing options...
falconvan Posted March 30, 2020 Report Share Posted March 30, 2020 Bought a bag of these off of Ebay 10 years ago and still using them Quote Link to comment Share on other sites More sharing options...
MarcDeSoto Posted March 31, 2020 Author Report Share Posted March 31, 2020 Thanks, falcon, they look good. It's simpler than I thought! Mine are all covered in undercoating, so they are probably still good. Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.