dontknowitall Posted July 22, 2011 Report Posted July 22, 2011 Ok, Engine is RUNNING! Yeah... but the Gearbox is making a vibrating type noise when put into first. all other gears are great . Have the rear wheels of the ground and is ok to put through the gears, except the noise in first gear! The book says the first gear is the same as the reverse so why no noise in reverse and only in first? Any Adjustments? Can it be I have assembled the top wrong when putting the lid back on? Quote
Desotodav Posted July 22, 2011 Report Posted July 22, 2011 Great job on getting it fired up Ryan. Not sure about the gearbox noise though. I'm sure that plenty of info will be forthcoming for you. Desotodav Quote
dontknowitall Posted July 22, 2011 Author Report Posted July 22, 2011 Hi davin, Tomorrow I will take the top of to have a look..I still have another box but I would have to change the fork over as it has different gearing, Quote
Dave72dt Posted July 22, 2011 Report Posted July 22, 2011 4 speed or 3? On a 4 speed, the shift collar has teeth on the outside and reverse is engaged on those teeth, not the inner ones as 1st gear would use. Otherwise I would suspect a bent fork or a chipped tooth. Quote
Dodgeb4ya Posted July 22, 2011 Report Posted July 22, 2011 Usually the 3 speeds are the problem transmissions. 4 speeds are tough! Quote
John-T-53 Posted July 22, 2011 Report Posted July 22, 2011 Too bad you're so far away... I have a good working 3 speed sitting on my garage floor with no home. Quote
dontknowitall Posted July 22, 2011 Author Report Posted July 22, 2011 thanks, John..the postage would kill the joy of sending it over! For all it is a tree speed box .... Quote
dontknowitall Posted July 23, 2011 Author Report Posted July 23, 2011 Thanks Kevin..it is indeed fantastic to hear her puring.. Congrats on gettin' her fired up! Quote
B1B Keven Posted July 23, 2011 Report Posted July 23, 2011 Did your parts make it across the pond yet? Quote
dontknowitall Posted July 23, 2011 Author Report Posted July 23, 2011 nope, still waiting for them..not in a hurry but then again the postal service here and overseas has become dismal. Did your parts make it across the pond yet? Quote
dontknowitall Posted July 23, 2011 Author Report Posted July 23, 2011 If I was to use a 4 speed floor change tranny instead of my 3 speed colom change would I have to change the diff? 1950 B2B Dodge Fargo Quote
mechresto Posted July 23, 2011 Report Posted July 23, 2011 In a nutshell, no 3spd or 4spd, in high gear they both run straight thru 1to1 so there are no changes to the top end speed however the lower end is slower on the 4spd. Quote
Merle Coggins Posted July 23, 2011 Report Posted July 23, 2011 In a nutshell, no3spd or 4spd, in high gear they both run straight thru 1to1 so there are no changes to the top end speed however the lower end is slower on the 4spd. Yea... what he said. Basically, a 4 speed is a 3 speed with an extra low, low gear. However, the bell housings are different if you're going to swap them. Quote
41/53dodges Posted July 24, 2011 Report Posted July 24, 2011 is your truck a column shifter? i almost wonder, if so, then what if the shifter were out of adjustment and did something to make it not mesh right? Quote
dontknowitall Posted July 24, 2011 Author Report Posted July 24, 2011 Well, that could well be! But I have removed the top of the box and fiddled with the gears putting it in what I think is the offending gear and indeed it vibrate and makes the noise with all the linkages removed... is your truck a column shifter? i almost wonder, if so, then what if the shifter were out of adjustment and did something to make it not mesh right? Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.