5027 steve
-
Posts
334 -
Joined
-
Last visited
Content Type
Links Directory
Profiles
Articles
Forums
Downloads
Store
Gallery
Blogs
Events
Everything posted by 5027 steve
-
Anyone on a lead for a new rear Hub????? Also any answer on being able to change to outer rear axle seal and if we have to remove backing plate to do it or can we pull it out and replace it without removing backing plate ...Thanks ......
-
Are these the two ports I would use for a remote oil filter????
-
Trying to dicern the shop manuel can the rear outer axle shaft deals be replaced without removing the brake backing plate???? I can't tell from the shop manual
-
Ok I need to post a parts wanted and for the life of me can't get to where to do it....I need a drivers side rear hub we do not need the drum .....just hub ...Thanks Steve
-
Merle u were exactly correct....I ordered one like u pictured.....mine is not beefy enough...THANK YOU AGAIN
-
Yep and it is checked to send me email but haven't recieved any Thanks ...
-
Merle coffins....how is that different than what I'm using???? This hub will not budge....tried low heat and nothing ...
-
I also used to get a email notification when someone relplied here but don't anymore?????
-
Ok I just tried for a 1/2 hour and must be stupid. Cause I can't find how to get to the parts wanted thread......
-
Also since I have the driveshaft out I want to replace the pinion seal...I take it I can remove the yoke nut and use a puller to remove yoke and replace seal......????
-
Thanks Merle I have a slide hammer puller that attached to the lugs ...I sprayed the axle the best I could with pb blaster gonna let it sit for a day and try again .....
-
Also whenever someone posts a link dust all thank you ....BUT when I click on them it never connects me but goes to a blank screen .....Thanks
-
-
Ok tank has no numbers and it only says "tanks" ......so I want to put a sending unit in it.....is it the hole closet in picture or the hole in the other side of the filler neck??????? Thanks
-
Results of dry compression test #1-88 #2-88 #3-88 #4-90 #5-88 #6-90 Engine gurus chime in please
-
Now into our questions for the weekend:::: OK we tried to remove the driver side rear hub using a 3 jaw puller and then a slide hammer and it will not move at all .......I think I have bearings seized to the axle ....Now What?????? I'm at a loss........Thanks
-
First and foremost I have to introduce my sidekick and truck mechanic my grandson Braxton ....He is by my side in the garage every weekend helping "Papa" rebuild and restore Braxton truck "Lucy" Braxton says thumbs up to all of you helping "US" with my sometimes silly questions...
-
Thanks
-
Ok has anyone ever changed the rear end yoke ???? To a newer style with straps and clamps???? I have to get a new Driveshaft made and was wondering if that's possible.....Thanks Steve ...
-
Really stupid question after I looked at my intake.....better question How do I delete a post?????
-
Ok this might be a silly question but will a offenhauser intake off a 225 slant 6 bolt up to our 218 flathead?????? Thanks
-
Ok previous owner was using 10w40 valvolone...
-
Yea like most of us I have no idea what the previous owner did ...from the things I see that he did I would not even ask him....scotch locks..burnt wires...etc so I'll just have to watch it after we change it....Thanks
-
Ok engine gurus...we have a few cases of this oil left from our drag racing days...it is very high in Zink and phosphates..=good for bearings....it is 10w30....can I use this in the flat head or is it a no no .....Thanks
-
Ok since I'm replacing the water pump I just read about a water distrabution tube in the head....is it standard practice to pull it out and check it ???? I believe this engine to be completely original having no work done to it.....Thanks
