bvilletrack Posted December 13, 2018 Report Share Posted December 13, 2018 Does anyone have a recommendation for a good quality head gasket? I'm in the process of replacing a blown head gasket on a 265. The old head gasket was a Fel-Pro with one side copper and the other fiber. I did use copper spray sealer on the copper side and left the "blue" side dry. But after a short time of use the copper side seems to have separated from the fiber and allowed coolant to leak into the space between Cylinder 1 and 2. Trying to figure out if I got a defective Fel-Pro gasket and if I would be better off using a double-sided copper gasket such as Best Gasket 510C. Thoughts? Thanks, DW Quote Link to comment Share on other sites More sharing options...
Plymouthy Adams Posted December 13, 2018 Report Share Posted December 13, 2018 before replacing a newly and low mileage gasket due to failure, read the crime scene and determine reason for failure....is your head flat without warpage issues and the block also flat and even....get a good machinist parallel bar and verify you are not installing a new gasket on a less than optimum engine component... 1 Quote Link to comment Share on other sites More sharing options...
bvilletrack Posted December 13, 2018 Author Report Share Posted December 13, 2018 Yep, the first thing I did was to check for flatness using a machinist bar. Checked both directions on the block and the head. Everything is within spec. Trying to figure out what when wrong continues to be a challenge. Quote Link to comment Share on other sites More sharing options...
Jeff Balazs Posted December 13, 2018 Report Share Posted December 13, 2018 Best is still the best. I had similar issues with the Felpro I fitted first. And re-torque at least 3 times at short intervals after it has come up to operating temp a few times. Hth, Jeff 1 Quote Link to comment Share on other sites More sharing options...
Plymouthy Adams Posted December 13, 2018 Report Share Posted December 13, 2018 (edited) Posted 1 hour ago Yep, the first thing I did was to check for flatness using a machinist bar. Checked both directions on the block and the head. Everything is within spec. Trying to figure out what when wrong continues to be a challenge. ok...the components are ready for a new gasket.....DO ENSURE...that you retorque the head after a heat cycle as specified in the manual....it is critical to allow proper squish of the material for sealing.. Edited December 13, 2018 by Plymouthy Adams Quote Link to comment Share on other sites More sharing options...
NiftyFifty Posted December 14, 2018 Report Share Posted December 14, 2018 Use the copper spray on every surface, that seems to have extended the periods between head gasket changes for me, and yes, re-torque after a couple of heating and cooling sessions Quote Link to comment Share on other sites More sharing options...
Matt Wilson Posted January 2, 2019 Report Share Posted January 2, 2019 (edited) Also, some of the threaded holes go into the water jacket. Be sure to use sealant on the head bolts that go into those holes. I believe Permatex high-temperature thread sealant has been used successfully by many for this purpose. Edited January 2, 2019 by Matt Wilson Quote Link to comment Share on other sites More sharing options...
torqczar Posted January 5, 2019 Report Share Posted January 5, 2019 no copper spray on PermaTorque head gaskets.. i looked it up on felpro site. if block and head are flat, check torque wrench calibration , the big snap on trucks have a machine to check. . copper spray , is a band aid to other problems... head and gasket need to be able to move around. the gaskets you buy today are light years ahead of '49 gaskets... why did you change head gasket in the first place? was it blown between 1 and 2? Quote Link to comment Share on other sites More sharing options...
JBNeal Posted January 5, 2019 Report Share Posted January 5, 2019 Maybe your head bolts were too long... Quote Link to comment Share on other sites More sharing options...
NiftyFifty Posted January 5, 2019 Report Share Posted January 5, 2019 FelPro just needs an out if the gasket fails and you used anything on it. These engines have imperfections and nobody is about to yank and disassemble the engine for a plaining when a little copper spray will do the trick. These flatheads ads were always tough on head gaskets, and if you do power improvements it can be a little worse. Spray it up, put a new gasket in and enjoy the road. Also get new head bolts from Summit if you haven’t already...they do stretch Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.