harmony Posted November 24 Report Posted November 24 I'm thinking about buying a 1940 Fargo but it needs a swing out windshield frame. I found one relatively reasonably priced on ebay but it says it's for a same vintage Powerwagon. So my question is, are the frames the same? The pictures shown seem to indicate that the frames are the same. Quote
Robert Harrison Posted November 24 Report Posted November 24 I cant definitively answer your question from the information provided. Typically though domestic Fargo vs Dodge frames are the same if the cabs look the same. Early on the military had domestic trucks that shared the same cabs with only minor changes to fuel fill location. The equivalent Fargo's year by year are typically the same except for the Fargo used the long engine and they had different chrome. The actual "Power Wagon" is a product made after the war and it had a similar cab although cab mounts were different than the 1940 models and I'm not really sure where the filler neck mounted. The military did not have Power wagons they had military trucks of various types so to say of the same period meaning 1940 when the Power Wagon came out after the war that would not be the same period. People use the term Power Wagon interchangeably when it really isn't They are somewhat similar to the WW2 stuff but are really not. If the truck the replacement frame came from after the and the cab looks the same it should fit. Otherwise DCM Classics reproduces them. They are often rusted out and once you blast them or have them dipped you really don't know what you are getting. DCM and MIdwest Military along with Vintage Power Wagons are some Helpful sources. Bob Harrison 1 Quote
harmony Posted November 24 Author Report Posted November 24 (edited) 1 hour ago, Robert Harrison said: I cant definitively answer your question from the information provided. Typically though domestic Fargo vs Dodge frames are the same if the cabs look the same. Early on the military had domestic trucks that shared the same cabs with only minor changes to fuel fill location. The equivalent Fargo's year by year are typically the same except for the Fargo used the long engine and they had different chrome. The actual "Power Wagon" is a product made after the war and it had a similar cab although cab mounts were different than the 1940 models and I'm not really sure where the filler neck mounted. The military did not have Power wagons they had military trucks of various types so to say of the same period meaning 1940 when the Power Wagon came out after the war that would not be the same period. People use the term Power Wagon interchangeably when it really isn't They are somewhat similar to the WW2 stuff but are really not. If the truck the replacement frame came from after the and the cab looks the same it should fit. Otherwise DCM Classics reproduces them. They are often rusted out and once you blast them or have them dipped you really don't know what you are getting. DCM and MIdwest Military along with Vintage Power Wagons are some Helpful sources. Bob Harrison This is how the listing is titled, " 1939-1947 Dodge Truck Wc Power Wagon Windshield Frame" so I'm thinking it would fit. I just want to be sure. I'm not paying monster prices for one though. This one is cheap compared to DCM's price. Edited November 25 by harmony Quote
harmony Posted November 25 Author Report Posted November 25 I'm also curious about the crank assembly or mechanism for controlling the movement of the window. I can't find any pictures or images or illustrations that show it. I also don't see any bracketry on the frame at the bottom in the centre that the mechanism would attach to in any of the frames I've seen on line. There is nothing on the truck (or the worn out frame) I'm thinking of buying and the owner can't remember if he has it somewhere burried in a box. He hasn't touched the truck in 20 years. Quote
Young Ed Posted November 25 Report Posted November 25 The opener attached to the bottom of the dash. The tape attached to the center bottom rail of the windshield frame via two very small screws. Quote
Veemoney Posted November 25 Report Posted November 25 2 hours ago, harmony said: I'm also curious about the crank assembly or mechanism for controlling the movement of the window. I can't find any pictures or images or illustrations that show it. Here is a replacement unit to give you an idea of what it looks like when not under the dash. New Replacement Closed-Cab Power Wagon Windshield Regulator - CC797133 – Vintage Power Wagons 1 Quote
harmony Posted November 25 Author Report Posted November 25 18 minutes ago, Veemoney said: Here is a replacement unit to give you an idea of what it looks like when not under the dash. New Replacement Closed-Cab Power Wagon Windshield Regulator - CC797133 – Vintage Power Wagons ohhhhh ok so now I know what I'd be looking for. Very interesting,,,, all except the price. Gulp!! Thanks for that link. Quote
harmony Posted November 25 Author Report Posted November 25 1 hour ago, Young Ed said: The opener attached to the bottom of the dash. The tape attached to the center bottom rail of the windshield frame via two very small screws. I couldn't figure out what you meant by "tape" but now after reading the discription in the link Veemoney sent me, I get it now. Quote
PT81PlymouthPickup Posted November 26 Report Posted November 26 It's difficult to find a good oem lower windshield frame section for a decent price. Most of the ones I've seen are severely rusted and require lots of work to restore. Some of the above mentioned venders are now selling brand new windshield frames for a bit over a grand $$$. I wonder if they're any good and how well they fit? Quote
harmony Posted November 26 Author Report Posted November 26 5 minutes ago, PT81PlymouthPickup said: It's difficult to find a good oem lower windshield frame section for a decent price. Most of the ones I've seen are severely rusted and require lots of work to restore. Some of the above mentioned venders are now selling brand new windshield frames for a bit over a grand $$$. I wonder if they're any good and how well they fit? Good point. I had given some thought to rebuilding the frame but both lower corners are worse than swiss cheese and pretty far gone. Belzona 1311 is pretty incredible stuff but just 2 litres of it is $830 Can. ouch!!. So I'd have to rebuild the lower corners, before pulling out the old glass for replacement. If all failed, a guy could make the windshielf fixed. Quote
Robert Harrison Posted December 3 Report Posted December 3 On 11/24/2024 at 6:25 PM, harmony said: I'm also curious about the crank assembly or mechanism for controlling the movement of the window. I can't find any pictures or images or illustrations that show it. I also don't see any bracketry on the frame at the bottom in the centre that the mechanism would attach to in any of the frames I've seen on line. There is nothing on the truck (or the worn out frame) I'm thinking of buying and the owner can't remember if he has it somewhere burried in a box. He hasn't touched the truck in 20 years. Quote
Robert Harrison Posted December 3 Report Posted December 3 As stated by another there is a tongue that bolts to the windshield frame with two tapped screws. It goes into a block in the windshield frame. There are two other similar blocks in the sides of the frame so it can be disassembled to replace the windshield. These blocks are available from DCM. They can be difficult to get apart frequently requiring drilling out the old screws. Also you find out what you have for a frame once you have it blasted. Often they are rusted out. There is an auto body product that is like bondo but has a high fiber content that can be used to till the holes. The original crank assemblies are commonly damaged since the windshield hinges freeze and people force the regulators. I have also seen guys sand cast replacement gears or weld them back up that sort of thing. I would not let the windshield crank slow you down from buying a good project. 1 Quote
Robert Harrison Posted Tuesday at 06:03 PM Report Posted Tuesday at 06:03 PM There is a super high fibrous body filler available I had a local shop fill mine with such look around and see what you can find. the stuff he showed me was Yellow from memory but I dont have the brand. Bob Harrison Quote
DJ194950 Posted Tuesday at 11:14 PM Report Posted Tuesday at 11:14 PM Something like this? https://www.ebay.com/itm/134639401579?var=0&mkevt=1&mkcid=1&mkrid=711-53200-19255-0&campid=5338767525&toolid=20006&customid=4581939849542915_710314500_s.06676375e98b1411be3d041ed6c22b98 Fiberglass reinforced body filler. .Many avail. colors, glass strand lengths, etc. are avail. DJ Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.