ggdad1951 Posted December 10, 2011 Report Share Posted December 10, 2011 so, I think I've found an interior rear view mirror.....anyone have a center bar they could take pictures of and dimensions of so at some point I can see if I can modify one someday to install the mirror? Quote Link to comment Share on other sites More sharing options...
B1B Keven Posted December 10, 2011 Report Share Posted December 10, 2011 The hole is 3 1/2" down from the spot where the arm starts the curve ( I hope you can understand that ). Quote Link to comment Share on other sites More sharing options...
Dodgeb4ya Posted December 10, 2011 Report Share Posted December 10, 2011 (edited) As seen here before... A factory original stamped 1948 Dodge 2-1/2 truck inside mirror division bar, and a NOS plain division bar. Mirror position is 6-1/2" down from the top. I have 2 of these genuine mirror division bars on my trucks. They are one the hardest factory accessories to see on a 1948-53 Dodge dodge truck. Edited December 10, 2011 by Dodgeb4ya Quote Link to comment Share on other sites More sharing options...
B1B Keven Posted December 10, 2011 Report Share Posted December 10, 2011 As seen here before... A original stamped 1948 Dodge truck inside mirror division bar, and a plain division bar.Mirror position is 6-1/2" down from the top. No wonder I have a hard time seeing behind me! Quote Link to comment Share on other sites More sharing options...
Desotodav Posted December 10, 2011 Report Share Posted December 10, 2011 I took my digital caliper measurements for you from the existing bar mounting holes Mark. The mirror mount hole in my truck centre bar is 3.348" down from the top mounting hole and 2.192" up from the second hole down in the centre bar. I used an original centre bar in my truck - it has a slightly recessed area where the mirror mounting arm secures to it with a square nut affixed to the centre bar at the back. Desotodav Quote Link to comment Share on other sites More sharing options...
ggdad1951 Posted December 10, 2011 Author Report Share Posted December 10, 2011 As seen here before... A factory original stamped 1948 Dodge 2-1/2 truck inside mirror division bar, and a NOS plain division bar.Mirror position is 6-1/2" down from the top. I have 2 of these genuine mirror division bars on my trucks. They are one the hardest factory accessories to see on a 1948-53 Dodge dodge truck. so you are saying you don't have an extra? Quote Link to comment Share on other sites More sharing options...
Dodgeb4ya Posted December 10, 2011 Report Share Posted December 10, 2011 Some where around here-my memory is slipping. I thought I had a case of 12 of these NOS mirror division bars and 3 or 4 aluminum dual heater valves, oh and a NOS 610T radio. I better look for this stuff before my days are done!!! Quote Link to comment Share on other sites More sharing options...
smallblockjunkie Posted December 10, 2011 Report Share Posted December 10, 2011 is this for a half ton or a bigger truck because this is what was in my half ton Quote Link to comment Share on other sites More sharing options...
VintageMoParts Posted December 14, 2011 Report Share Posted December 14, 2011 (edited) I'd love a chrome division bars to hold my mirror. Been thinking of just drilling a hole in mine, probably a bad idea.. Any ideas what this one would go to? It's got me stumpped Edited December 15, 2011 by VintageMoParts Quote Link to comment Share on other sites More sharing options...
Young Ed Posted December 14, 2011 Report Share Posted December 14, 2011 Looks like a 39-47 truck. Maybe earlier trucks too. I might be interested. Quote Link to comment Share on other sites More sharing options...
ggdad1951 Posted December 14, 2011 Author Report Share Posted December 14, 2011 Some where around here-my memory is slipping. I thought I had a case of 12 of these NOS mirror division bars and 3 or 4 aluminum dual heater valves, oh and a NOS 610T radio. I better look for this stuff before my days are done!!! dibs on anything you find in that list! Quote Link to comment Share on other sites More sharing options...
Reg Evans Posted December 14, 2011 Report Share Posted December 14, 2011 is this for a half ton or a bigger truck because this is what was in my half ton That type came from the later 50's and early 60's trucks. Here's one in my 58 Sweptside. Quote Link to comment Share on other sites More sharing options...
TheMoose Posted December 14, 2011 Report Share Posted December 14, 2011 I thought I'd scored an interior mirror but while it fits over the trim great the holes are not far enough apart to line up. I may go ahead and drill the extra hole in the trim, I think it'll look good. Quote Link to comment Share on other sites More sharing options...
ggdad1951 Posted December 14, 2011 Author Report Share Posted December 14, 2011 just so you know that is a car hood ornament in the picture....I'm gonna have to wait to find the right bar before I mount my mirror...which might be a LOGN time if ever! Quote Link to comment Share on other sites More sharing options...
TheMoose Posted December 14, 2011 Report Share Posted December 14, 2011 (edited) just so you know that is a car hood ornament in the picture....I'm gonna have to wait to find the right bar before I mount my mirror...which might be a LOGN time if ever! The hood ornament has the correct end on it where the one on my truck now has a tab at the rear for another trim piece it'll work until I find the correct truck hood ornament. Picked it up at a local pawn shop for $40 so it's closer to right than the one that was on there. Edited December 14, 2011 by TheMoose Quote Link to comment Share on other sites More sharing options...
ggdad1951 Posted December 14, 2011 Author Report Share Posted December 14, 2011 I actually have one of those as well, but I'm gonna use it for a handle on a bed storage box for my truck Quote Link to comment Share on other sites More sharing options...
Dodgeb4ya Posted December 15, 2011 Report Share Posted December 15, 2011 (edited) The hood ornament has the correct end on it where the one on my truck now has a tab at the rear for another trim piece it'll work until I find the correct truck hood ornament.Picked it up at a local pawn shop for $40 so it's closer to right than the one that was on there. Probably everyone will be happy if you just use the 1948-50 correct optional hood ornament for the 1951-3 B3 and B4 trucks. I will always like and use the 1953 "Horney" 1953 Dodge car ornament for my 1951-53 trucks-it's really a cool hood ornament! Edited December 15, 2011 by Dodgeb4ya Quote Link to comment Share on other sites More sharing options...
Young Ed Posted December 15, 2011 Report Share Posted December 15, 2011 As a followup this part # is listed for 41-47 dodge trucks. It will be on its way to my house shortly I'd love a chrome division bars to hold my mirror. Been thinking of just drilling a hole in mine, probably a bad idea..Any ideas what this one would go to? It's got me stumpped http://vintagemoparts.com/product.php?id_product=124 Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.