jmooner3

The one in my 50 parts truck had a seam, it was rotted out and it was nasty. The seam was hanging open, I guess it was ventilation for the mice family living in there. I decided to try a one piece, on my 49 and it came out alright. Im happy with it, I’m always interested in what others have done. Most of what was needed done on this truck- I did research and then just winged it. Rather than several hundred dollars to buy the pre fabbed Kit, Im all in for ~$100.... saved a few bucks, it turned out ok AND I got to spend another couple days in old blue. ?

It is a 4x8 sheet of 1/8” abs. It does have texture on one side and smooth on other. I left the textured side out. The SEM paint is at our local Napa, you prob can get it on line. It’s cordovan brown.

Thanks guys. My truck had some desktop car parts so maybe they’re from a desoto, the brackets look like yours and screw holes line up. I’m going to revamp them and make em work. Appreciate the feedback!

Above the windshield there are Holes for a small tag, one side had the seat instructions, looks like there are holes for same size tag on other side... any idea what goes there?

I have a set of sun visors, look to be original. Seems the passenger side is rare. I’ve cleaned up the steel to a pretty good luster, pulled the visors off the metal rod, the visor material is a perforated cardboard/ vinyl type material and there was a nasty crumbling wood grain contact paper glued over it. I was able to heat and peel the paper off. I’m curious if these would have been original. The mounting looks like the pics that others have posted. I’m interested in your thoughts on how to refurbish them. Thx.

I finally got interior into Ol Blue. Reg had sent me his pattern and I was going to copy and cover with vinyl... instead I altered it a bit when I found a sheet of 1/8” abs. I made the two door cards and the two piece back for our 5 window rigs, but given that ABS can be heated and bent I tried making top and wing panels out of one piece. Bent it and glued the corners with acetone and abs chunks melted to make a one piece head liner. I cut a small relief at back center to give it right curve in 2 dimensions. I did a small seam at back. I had to install back piece at windows first then top so not as it was from factory but it went together with some choice words. I could use a matching set of window cranks if anyone knows s source. I used rivnuts and 10-24 stainless screws with finish washers to fasten. ABS panel was black so I painted with SEM brown, snagged some arm rests from an 80s Toyota painted and voila... what d ya think?

wrapping up another summer of running Ol blue around and had a great drive today, figured I’d share a pic on this thread of fall in Vt.

Here’s one from my front yard today, it’s hard to beat a fall B1B pilothouse drive in VT. ?

230 flattie in 1949 B1B mated to 3speed tranny. Yep the stock set up is about 45 top end for me too. I don’t need to pass everyone on the road but it’d be nice to be able to keep up. I just plan ahead to be on time, stay on the secondary roads, and enjoy the ride! cheers, jay

Thanks Plymouthy -I've got an engine block that I'm tearing down and going to rebuild, once I have it gutted I'm hauling it in this truck to the machine shop to get it bored and ready to pump again. Can't wait to pull up in this thing to give them that greasy old block... I decided when I made the call to go with the finished boards that I'm still going to use it. I might throw a piece of plywood in and probably not going to haul cow manure in it as I have a trailer for that, but I did haul kayaks, a paddle board, and my bride to the local reservoir. (One of them rode in the front, the rest in the back). :-0

Here's the update on Ol Blue's journey, I finished the bed this week. I hauled home some rough cut mahogany, planed, milled rabbited to accept the metal strips, oiled it and installed....what-dya think?

Agreed, pull the floor pans - the engine, bell housing, pedals and all come out... there are four bolts horizontal into the housing at rear of engine and then the two up front. The engine can be manipulated to get pedals to clear under the firwall. Up and out...The whole enchilada comes out as one. I did mine after pulling the "doghouse" off. Estrada motor sports has some videos showing how to do it.

Nice job and happy to see another Mopar running the roads of the NorthEast!

Hey Mark, agreed rough cut would probably fit my truck better, I have rough cut Oak too, but I skip planed one of the mahogany boards and it's beautiful! Hek boats use Mahogany out in the weather, I'm a woodworker too so I think I'm going to plane, clean the boards up, and just oil them to let the grain show. I still use it as a truck, if I haul nasty junk maybe I'll put a piece of plywood over it, but each ding ads character ;-). Whatya think of your running boards reworked, revived, shortened, and in service...

Fixed running boards, fixed overheat, and been driving daily, built a back bumper, hauled some rough cut mahogany home this week to make a bed for ol blue. Also took my first night run in the rain the other night. Lights worked and so did the wipers....