Instructions, Manuals & Templates
Instructions sheets, manuals and templates for missing parts.
101 files
-
Mopar Factory PCV System
Mopar Factory PCV System how to.
2,152 downloads
- Mopar Factory PCV System
- Engine
- (and 3 more)
Updated
-
1948-1949 Dodge Truck Drivers Manual PDF
60 Page Downloadable PDF Drivers Manual for the 1948-1949 Dodge "Job Rated" Trucks.
Series B-1-B and B-1-C
These were very detailed manuals and can be very useful in keeping your Pilothouse on the road.
Buy more online at www.vintagemoparts.com
141 downloads
- pilothouse
- driver
- (and 3 more)
Updated
-
MoPar Oil Filter Installation Instructions
MoPar Micronic Oil Filter Element Installation Instructions
Model Application:
Plymouth 1934-42 – All Models
Plymouth Commercial 1937-41 – All Models
Dodge 1934-42 – All Models
DeSoto 1934-42 – All Models
Chrysler Six 1934-42 – All Models
Chrysler Eight 1940-42 – All Models
Dodge Truck 1934-45 – All Models Except Diesel & 3 Ton
MoPar Micronic Oil filter element 861032 can be used to replace other make elements as listed below:
Purlator PN-15
Purolator N-15
AC C-301
AC C-29
Fram C-130
Walker RC-23
Wix PC-80N
DeLuxe C-64P
134 downloads
0 comments
Submitted
-
1936-1942 Plymouth Service Manual
By jcmiller
This is an abridged service manual covering Plymouth cars from 1936-1942.
226 downloads
Submitted
-
Flathead 6 Engine Rebuild.pdf
By Mark D
Four Part Auto Restorers Magazine article which describes the Flathead 6 teardown and rebuild completed by the author Curt McConnell. 21 pages - pdf format.
612 downloads
Submitted
-
Fulton Sun Visor.pdf
Comprehensive Data and Directions for Assembling, Painting and Installing FULTON SUN SHIELD
139 downloads
0 comments
Updated
-
Vacuum gauge chart
By Alshere59
A basic chart that gives typical readings for trouble shooting.
120 downloads
0 comments
Updated
-
Mopar 802 Radio Custom Controls Installation Instructions
Mopar 802 Radio Custom Controls Installation Instructions
Part No. 1161462 for use with Model 802 Radio on 1946 and 1942 Dodge
83 downloads
0 comments
Submitted
-
Borg-Warner OD Solenoid Repair Instruction
By DJ194950
Hope pages are in order, but I'm not into computers, just hope it's a help to someone!
Doug
182 downloads
Updated
-
MoPar Oil Filter Adapter Package Installation Instructions
MoPar Oil Filter Adapter Package Installation Instructions for hrift Type MP 701 - Part No. 1123152 For replacing sealed type filter
104 downloads
0 comments
Submitted
-
MoPar License Plate Frame Installation Instructions
Instructions for installing MoPar License Plate Frame
Part #1692 666
33 downloads
0 comments
Submitted
-
Fuel pump heat shield template
By TodFitch
Dimensioned drawing of fuel pump heat shield.
240 downloads
Updated
-
Pertronix Electronic Ign. Coverersion Part #'s Per Dist.#
By DJ194950
For those that inquire about this changeover to see if Pertonix makes a conversion to fit their Dist. as installed in their car!
Year of car/ motor does not make a difference as most can used in many models depending on engine size, BUT I am not adding about differant advance curves, etc of various models.!--Only the Dist. being used! To look at what's avail. Do not want to open that canOworms!
If/when you locate appropiate # for changeover, I'd suggest googling the Pertronix number and compare prices. Seems to me the last time I was looking , prices where as much as $50.00 variation!
Doug
Added more info that I left out before, more distributor #'s for apps.
Adding several install sheets for 6v. pos. ground pertronix ign. sheets to show most changeover info.
Thanks,
Doug
468 downloads
0 comments
Updated
-
Updated
-
R-10 OD controls, R-10 OD maintenance,R-10 operation
By DJ194950
Factory, training for R-10 Overdrive transmissions
Shared with me by Jim Yergins (forum member) approx. 2 years ago, thanks again!
497 downloads
0 comments
Updated
-
Submitted
-
0 comments
Updated
-
BW_OD_Info.pdf.zip
Instruction manual for BW overdrive .
103 downloads
- Reference
- over drive
- (and 1 more)
0 comments
Updated
-
Heater Model 504 Installation Instructions.pdf
By P15-D24
Factory installation instructions for Fresh Air heater for B Series trucks.
149 downloads
0 comments
Submitted
-
Inner Fender to Frame Seal Template
By Conn47D24
This template can be used to trace and cut out the masticated rubber seals between the Front, INNER fenders, and the frame.
They are stapled on to each inner fenders ( driver and passenger ).
I was lucky to purchase both inner fenders NOS with the original rubber seals attached. I am sharing them here for your use. I have benefited from help here on other templates so I am paying it forward.
Instructions:
Purchase a sheet / roll of masticated rubber. 1/8 " thick min. ( like tire rubber with poly cord imbedded )
Print the templates on LEGAL size paper ( 8.5 " X 14 ")
Match the two pages where shown and tape the sheets together.
Cut out the template
Trace on to the rubber sheet ( bright color pen / marker )
Cut out the rubber seal.
I used heavy gauge stainless steel wire to make the " staples " and wired the seals to the inner fenders.
Note: my D24 is a Club Coupe, I believe the front fenders are the same on other Models and maybe Chysler's other lines.
Good Luck !
Clay Janer
Conn47D24
173 downloads
0 comments
Updated
-
0 comments
Submitted
-
1947 Owner’s Manual Mopar Radio Model 802 Plymouth Dodge DeSoto Chrysler
By linus6948
1947 Owner’s Manual Mopar Radio Model 802 Plymouth Dodge DeSoto Chrysler
Sorry for the upside down scans
321 downloads
0 comments
Submitted
-
Flashing/Polarizing Generator guide
By Alshere59
Polarization restores the residual magnetism in the cores of the generator field poles so that when the generator starts charging it will do so in the proper polarity.
It is usually not necessary to re-polarize unless the generator has been removed and repaired or the regulator has been changed. If this has occured, then re-polarization should be done before starting the engine. Otherwise, the generator may not charge or it could charge in the reverse direction.
Re-polarizing is relatively easy to do. All that is necessary is to briefly connect the generator armature to the battery hot terminal. The most convenient way to do this is to take a short jumper wire and touch it to the "Batt" and "Gen" terminals on the voltage regulator. At the moment of contact you should see a slight spark. This indicates that the process is completed.
It should be noted that it is the generator that is being polarized, not the regulator.
97 downloads
- Charging
- Electrical
- (and 1 more)
0 comments
Updated
-
Windshield_Wiper Gaskets (1).pdf
By P15-D24
Windshield Wiper Gaskets template posted by HanksB3B
80 downloads
0 comments
Submitted
-
Radiator Seal
Factory P15 front radiator seal to improve air flow through the radiator.
86 downloads
0 comments
Updated