Instructions, Manuals & Templates
Instructions sheets, manuals and templates for missing parts.
101 files
-
Mopar Factory PCV System
Mopar Factory PCV System how to.
2,152 downloads
- Mopar Factory PCV System
- Engine
- (and 3 more)
Updated
-
Inner Fender to Frame Seal Template
By Conn47D24
This template can be used to trace and cut out the masticated rubber seals between the Front, INNER fenders, and the frame.
They are stapled on to each inner fenders ( driver and passenger ).
I was lucky to purchase both inner fenders NOS with the original rubber seals attached. I am sharing them here for your use. I have benefited from help here on other templates so I am paying it forward.
Instructions:
Purchase a sheet / roll of masticated rubber. 1/8 " thick min. ( like tire rubber with poly cord imbedded )
Print the templates on LEGAL size paper ( 8.5 " X 14 ")
Match the two pages where shown and tape the sheets together.
Cut out the template
Trace on to the rubber sheet ( bright color pen / marker )
Cut out the rubber seal.
I used heavy gauge stainless steel wire to make the " staples " and wired the seals to the inner fenders.
Note: my D24 is a Club Coupe, I believe the front fenders are the same on other Models and maybe Chysler's other lines.
Good Luck !
Clay Janer
Conn47D24
173 downloads
0 comments
Updated
-
SHIFTRITE PAGE 1a.jpg
By Mark D
Manufacturers installation brochure for the Shift Rite column mounted overdrive control.
154 downloads
0 comments
Updated
-
Radiator Seal
Factory P15 front radiator seal to improve air flow through the radiator.
86 downloads
0 comments
Updated
-
Updated
-
0 comments
Updated
-
Flashing/Polarizing Generator guide
By Alshere59
Polarization restores the residual magnetism in the cores of the generator field poles so that when the generator starts charging it will do so in the proper polarity.
It is usually not necessary to re-polarize unless the generator has been removed and repaired or the regulator has been changed. If this has occured, then re-polarization should be done before starting the engine. Otherwise, the generator may not charge or it could charge in the reverse direction.
Re-polarizing is relatively easy to do. All that is necessary is to briefly connect the generator armature to the battery hot terminal. The most convenient way to do this is to take a short jumper wire and touch it to the "Batt" and "Gen" terminals on the voltage regulator. At the moment of contact you should see a slight spark. This indicates that the process is completed.
It should be noted that it is the generator that is being polarized, not the regulator.
97 downloads
- Charging
- Electrical
- (and 1 more)
0 comments
Updated
-
Fulton Sun Visor.pdf
Comprehensive Data and Directions for Assembling, Painting and Installing FULTON SUN SHIELD
139 downloads
0 comments
Updated
-
0 comments
Submitted
-
BW_OD_Info.pdf.zip
Instruction manual for BW overdrive .
103 downloads
- Reference
- over drive
- (and 1 more)
0 comments
Updated
-
0 comments
Updated
-
STEERING WHEEL RESTORATION HANDBOOK From Antique to Milestone FOR FUN AND PROFIT 1981.pdf
By billrigsby
STEERING WHEEL RESTORATION HANDBOOK From Antique to Milestone FOR FUN AND PROFIT 1981
14 downloads
0 comments
Submitted
-
Mopar Body and Sheet Metal Quick Reference Shop Manual 1940 thru 1948
By Pep48
370 pages. Lists part numbers, and exploded views of various body panels. The beginning of the manual lists the starting and ending serial #'s as well as which plant manufactured the car (if you cross reference the mfg plants, you can see total number of models produced. Plymouth, Dodge, Desoto, Chrysler.
Published in 1949 and covers 1940 thru 1948.
13 downloads
0 comments
Submitted
-
6 volt to 12 volt Light Bulb interchange chart
By Pep48
Handy chart that gives you the 12 volt equivalent for 6 volt bulbs. Handy if you are doing a 12 volt upgrade. No more endless hours at the auto parts store.
16 downloads
0 comments
Submitted
-
Back up Light Kit Instruction & Template sheets for OEM Mopar 1948
By Pep48
This was a dealer accessory. The instructions are .pdf files so that you can enlarge them easily. Pics show what came in the kit.
50 downloads
0 comments
Submitted
-
Fenton Header installation instructions
By Alshere59
Installation instructions for the original Fenton headers. May help others with headers for pipe layout but a cross over pipe would be required.
80 downloads
0 comments
Updated
-
radio_noise_suppression.pdf
By P15-D24
Set of instructions for installing radio noise suppression devices.
51 downloads
- radio
- radio noise
- (and 1 more)
0 comments
Submitted
-
Fuel pump heat shield template
By TodFitch
Dimensioned drawing of fuel pump heat shield.
240 downloads
Updated
-
0 comments
Updated
-
MITCHELL ILLUSTRATED PARTS CATALOG 1933 - 1954 All Mopar
By Pep48
This is an illustrated parts catalog with the name of the part, Factory Part Numbers as well as Mitchell Numbers.
It shows exploded views and is organized in 17 part groups (99 pages.)
Chrysler, Plymouth, Dodge, Desoto
Very useful !
30 downloads
0 comments
Submitted
-
Plymouth Service Manual Models P15, P17 and P18, P19 and P20 (Publication # D-13251)
By Eneto-55
This manual was copied using a scanner that includes the de-screening process, which is designed to eliminate the 'cross-hatching' that results from scanning photos that were originally printed using the standard screening process. (This prevented dark and shaded areas of the photos from coming out completely black.)
I have not been able to make monetary contributions to the forum, so this is my contribution, based on many hours of work. I attempted to adjust each page in the scanner so that they would not be at an angle.
My only requests for those who download it are:
01.) enjoy it, and
02.) if you are able, make some contribution to the operation of the forum.
Thank you to all of the members here who have freely contributed their scanning work in the past.
22 downloads
0 comments
Submitted
-
Vacuum gauge chart
By Alshere59
A basic chart that gives typical readings for trouble shooting.
120 downloads
0 comments
Updated
-
Windshield_Wiper Gaskets (1).pdf
By P15-D24
Windshield Wiper Gaskets template posted by HanksB3B
80 downloads
0 comments
Submitted
-
Heater Model 504 Installation Instructions.pdf
By P15-D24
Factory installation instructions for Fresh Air heater for B Series trucks.
149 downloads
0 comments
Submitted
-
R-10 OD controls, R-10 OD maintenance,R-10 operation
By DJ194950
Factory, training for R-10 Overdrive transmissions
Shared with me by Jim Yergins (forum member) approx. 2 years ago, thanks again!
497 downloads
0 comments
Updated