DollyDodge Posted October 5, 2011 Report Share Posted October 5, 2011 Lately my front right while started sticking and pulling a bit, this weekend, the right front brake would nearly lock up when just touching the brake pedal. Is this a failing or malfunctioning wheel cylinder, or is something else going on? All the other brakes work normally. Quote Link to comment Share on other sites More sharing options...
John-T-53 Posted October 5, 2011 Report Share Posted October 5, 2011 Sounds like a leaking wheel cylinder or fitting! When the shoes get soaked, it's imperative they're replaced. Quote Link to comment Share on other sites More sharing options...
B1B Keven Posted October 5, 2011 Report Share Posted October 5, 2011 Sounds like a leaking wheel cylinder or fitting! When the shoes get soaked, it's imperative they're replaced. X's 2. Quote Link to comment Share on other sites More sharing options...
oldmopar Posted October 5, 2011 Report Share Posted October 5, 2011 Are you losing brake fluid,check the inside of the wheel sometimes it will run down if its leaking bad. In any case pull the drum of before you go for another ride. Quote Link to comment Share on other sites More sharing options...
tinlizzy Posted October 6, 2011 Report Share Posted October 6, 2011 Or you might look at the opposite side, one locking up may be doing the work of both, here again leaking wheel cyclinder juicing the brake pads and not grabbing. Just a thought. Quote Link to comment Share on other sites More sharing options...
catfishcuz Posted October 6, 2011 Report Share Posted October 6, 2011 Or you might look at the opposite side, one locking up may be doing the work of both, here again leaking wheel cyclinder juicing the brake pads and not grabbing. Just a thought. I agree i would pull both of front drums i have seen that exact thing happen before on drum brakes. Butch Quote Link to comment Share on other sites More sharing options...
MBF Posted October 6, 2011 Report Share Posted October 6, 2011 If you've got a front brake locking up I'd also check the back brakes to make sure that they're working. I've seen that in a truck a few years back. Chances are if you got a cylinder crudded up or leaking the others may not be in much different shape. I'm in the process of replacing all of my cyls and lines right now. Mike Quote Link to comment Share on other sites More sharing options...
coW52Dodge Posted October 6, 2011 Report Share Posted October 6, 2011 FWIW, I've seen old rubber hoses cause sticky brake problems like that on different cars. Something to check, in case the other far more likely suggestions are not the problem. Quote Link to comment Share on other sites More sharing options...
DollyDodge Posted October 7, 2011 Author Report Share Posted October 7, 2011 A year ago I replaced all the hoses, rebuilt the wheel cylinders, and put in a new master cylinder. I don't see any signs of leaking (including the level in the master cylinder stays the same). I will pull the drums this weekend and have a looksee. The other brakes seem to be fine. Quote Link to comment Share on other sites More sharing options...
TheMoose Posted October 7, 2011 Report Share Posted October 7, 2011 A year ago I replaced all the hoses, rebuilt the wheel cylinders, and put in a new master cylinder. I don't see any signs of leaking (including the level in the master cylinder stays the same). I will pull the drums this weekend and have a looksee. The other brakes seem to be fine. Sounds like mine, all new brakes but RF will lock at the touch of the brakes on occasion. I'd be interested to see what you find or if I get to mine first I'll let you know what I find Quote Link to comment Share on other sites More sharing options...
HanksB3B Posted October 7, 2011 Report Share Posted October 7, 2011 (barring any fluid saturation) your brakes need to be adjusted. What happens over time is that the pad wear tends to become eccentric causing a brake wedgie. Hank Quote Link to comment Share on other sites More sharing options...
TheMoose Posted October 7, 2011 Report Share Posted October 7, 2011 (barring any fluid saturation) your brakes need to be adjusted. What happens over time is that the pad wear tends to become eccentric causing a brake wedgie.Hank But my truck has about 100 miles on it since brakes were done, but it also has several years since they were done. Quote Link to comment Share on other sites More sharing options...
HanksB3B Posted October 7, 2011 Report Share Posted October 7, 2011 It's a smaller problem than you think. It's just that with the toe and heel adjustment too much toe causes the wedgie effect. Without jacking the truck up just get under there with the proper wrenches and readjust a little by feel do be familiar with what tightens and loosens the tolerance between the pad and shoe. It's been a while, Hank Quote Link to comment Share on other sites More sharing options...
DollyDodge Posted October 11, 2011 Author Report Share Posted October 11, 2011 hmmm.......I think my truck is messing with me. I drove it this weekend and had no brake issues at all. It definately isn't leaking though. I wish I had one of the brake gauges to properly adjust them. I used a method listed in this forum for adjusting without the guage, it took a long time, and until the brake locking situation they seemed to work fine. I will look at the adjustment again. Quote Link to comment Share on other sites More sharing options...
Reg Evans Posted October 11, 2011 Report Share Posted October 11, 2011 I would lend you my Ammco 1750 with a hefty deposit and the cost of shipping. Quote Link to comment Share on other sites More sharing options...
jpwuertz Posted October 11, 2011 Report Share Posted October 11, 2011 Since we are on the topic of brakes, I am looking for some replacement shoes for the front (10 inch) shoes for a B3B 1/2 ton. I have watched ebay but have not found any 10 inch. Quote Link to comment Share on other sites More sharing options...
B1B Keven Posted October 11, 2011 Report Share Posted October 11, 2011 Since we are on the topic of brakes, I am looking for some replacement shoes for the front (10 inch) shoes for a B3B 1/2 ton. I have watched ebay but have not found any 10 inch. Here ya go. Roberts are cheaper as there is no core charge. http://www.robertsmotorparts.com/truck_parts.asp?Action=search&c=Trucks+%2D+Brake+Parts http://www.hagensautoparts.com/1953/DODGE+-+Truck/B4B+1%2502F2ton+217.8-6cyl+108wb/BRAKE+-+Cylinders%2C+hoses%2C+kits+%26+shoes/All/ Quote Link to comment Share on other sites More sharing options...
DollyDodge Posted October 11, 2011 Author Report Share Posted October 11, 2011 Reg: I may hit you up for the gauge later on next year after I get the engine out and rebuilt, and then do a better job on my brakes. Thanks for the offer Quote Link to comment Share on other sites More sharing options...
homer2105 Posted January 28, 2012 Report Share Posted January 28, 2012 I'm in the process of doing complete brake job on a '48 D24. Have rebuilt master and all 6 slaves, replaced all hard lines, replaced hoses, had shoes relined and drums turned. I have 3 differnent lengths of the push rods that go between the slave and the shoe. What's up with that? Does anyone have a complete set of the ones I should have? Next have to adjust brakes (major and minor) add fluid (Dot 5?). When I go to adjust major the bolt tightens. Is that right? Thnks , Bruce Quote Link to comment Share on other sites More sharing options...
homer2105 Posted February 14, 2012 Report Share Posted February 14, 2012 I could have sworn I posted a question as to adjusting my brakes on my D24 the other day but I'll be dipped if I can find it. This must be part of getting long of tooth and grey of muzzle, if any body finds me, let me know! Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.