Jump to content

lugnut123

Members
 View Profile  See their activity

  • Posts

    306

  • Joined

  • Last visited

 Content Type 

Everything posted by lugnut123

  1. lugnut123
    A friend of mine put a 6 cyl perkins out of a combine ina chevy 1 ton service truck he had. It would haul a heck of a load. He had to browny for an overdrive so it would make high way speeds. It made good milage to for all the wieght it was hauling.
  2. lugnut123
    If the coil has an internal resister and you put 12 v into the coil will the voltage on the negitive side of the coil be 6 volt?? Just a thought that accurded to me.
  3. lugnut123
    Hank I ain't complainin.!!
  4. lugnut123
    Is that a 4BT cummins??
  5. lugnut123
    The wire that activates the cilinoid is on the acc side insted of the starter side.
  6. lugnut123
    Where would you find a grill like the one in this truck?? It looks good.
  7. lugnut123
    those look like the rivets I have in my leather belt. They unscrew.
  8. lugnut123
    it looks like you just lube up under the rubber and give it a solid pull.I got my rubber to move back and forth alittle bit without any lube so it should come off with a little cussin and pullin. I'll let you know in the morning.
  9. lugnut123
    thanks everyone. I'll getr dun in the mornin. I'm gonna slap a coat of hunter green on the old beast.
  10. lugnut123
    I have the cover off the inside of the door. It looks like there is a rubber( hard plastic) bumper on the end of the flat door stopper rod. Can it be taken off? I have seen them door stops with cotter pins in them instead of a rivet. thanks Hank
  11. lugnut123
    A b1c have the same wheel pattern as a early 80's chevy 5 hole 1/2 ton pickup. Replace your whole rrend with the chevy. Put in a T-5 chevy 5 speed tranny and use the chevy driveline. U mite save some moneys. I ended up spending 200-250$ on a driveline with that special flange that fits the dodge 4 speed. You have to rig a slip joint in your driveline also. With the flange you will use a small GM u joint.
  12. lugnut123
    One of my old trucks I tryed to put a newer dual M/C in without any valves. I piped the outlets together then to the wheel cylinders and couldn't get the M/C to work. I finally went back to the original equipment and to works now. Maybe if I had ran it through a porpotioning valve it would have worked?
  13. lugnut123
    I figure grind the top off of the rivet. Like you said carefully!!! I'll do it inda morning. thanks Hank
  14. lugnut123
    do you have the original axels still on your truck?
  15. lugnut123
    How do you remove the little door stopper .The part that keeps your door from opening to far? It looks like there is a small rivet holding one end. Do you drill the rivet and replace it later??
  16. lugnut123
    I have a bucket of 80/90 in the tractor shed so I think i'll try it first.. Thanks Hank and everyone.
  17. lugnut123
    I think I must have a syncro ed 4 speed. It shifts to easy to be a non. I haven't really got this old truck out on the road and ran it hard yet. I think I'll change the oil in the tranny and give it a go before I tear any thing apart. What do you think 80/90 or 85/140 gear oil for the tranny?? thanks everyone.
  18. lugnut123
    I have a b-3-c and I was wondering how hard it is to rebuild a 4 speed tranny? How much for a bearing kit? Is that tranny winey sound usually worn bearing or? Any where do they sale kits? Just looking at opions . thanks everyone.
  19. lugnut123
    i seen a pierce arrow bus kinda like that. It had doors down both sides and was about a ton and a half truck frame. It was down on route 66 in new mexico in a farmers lot.
  20. lugnut123
    If you mount your rack and pinion on the frame wouldn't the wheels toes in and out as the springs flex up and down?
  21. lugnut123
    Mario for a carb rebuild kit. It's carquest number 101a . Thats for a carter BB carb. good luck
  22. lugnut123
    The base plate gasket on your carb has 4 unward looking grooves that let a little vacum port on the bottom of your carb suck air. If the wrong gasket was installed your engine mite run ruff. Just an idea.
  23. lugnut123
    A larger cable will carry more amps which is what you want with 6 volts.
  24. lugnut123
    B-1-B panel truck on craigs list Albuquerque ,new mexico. 800$ It's listed as a 1947.
  25. lugnut123
    your carb should have a vaccum port in it's base. If you don't havee the right base gasket your moter mite run bad . just thinking out loud. good luck
×
×
  • Create New...

Important Information

We have placed cookies on your device to help make this website better. You can adjust your cookie settings, otherwise we'll assume you're okay to continue.

Terms of Use