Instructions, Manuals & Templates
Instructions sheets, manuals and templates for missing parts.
98 files
-
Borg-Warner OD Solenoid Repair Instruction
By DJ194950
Hope pages are in order, but I'm not into computers, just hope it's a help to someone!
Doug
182 downloads
Updated
-
1948-1949 Dodge Truck Drivers Manual PDF
60 Page Downloadable PDF Drivers Manual for the 1948-1949 Dodge "Job Rated" Trucks.
Series B-1-B and B-1-C
These were very detailed manuals and can be very useful in keeping your Pilothouse on the road.
Buy more online at www.vintagemoparts.com
139 downloads
- pilothouse
- driver
- (and 3 more)
Updated
-
MoPar License Plate Frame Installation Instructions
Instructions for installing MoPar License Plate Frame
Part #1692 666
33 downloads
0 comments
Submitted
-
MoPar Oil Filter Installation Instructions
MoPar Micronic Oil Filter Element Installation Instructions
Model Application:
Plymouth 1934-42 – All Models
Plymouth Commercial 1937-41 – All Models
Dodge 1934-42 – All Models
DeSoto 1934-42 – All Models
Chrysler Six 1934-42 – All Models
Chrysler Eight 1940-42 – All Models
Dodge Truck 1934-45 – All Models Except Diesel & 3 Ton
MoPar Micronic Oil filter element 861032 can be used to replace other make elements as listed below:
Purlator PN-15
Purolator N-15
AC C-301
AC C-29
Fram C-130
Walker RC-23
Wix PC-80N
DeLuxe C-64P
133 downloads
0 comments
Submitted
-
Mopar 802 Radio Custom Controls Installation Instructions
Mopar 802 Radio Custom Controls Installation Instructions
Part No. 1161462 for use with Model 802 Radio on 1946 and 1942 Dodge
82 downloads
0 comments
Submitted
-
MoPar Oil Filter Adapter Package Installation Instructions
MoPar Oil Filter Adapter Package Installation Instructions for hrift Type MP 701 - Part No. 1123152 For replacing sealed type filter
104 downloads
0 comments
Submitted
-
R-10 OD controls, R-10 OD maintenance,R-10 operation
By DJ194950
Factory, training for R-10 Overdrive transmissions
Shared with me by Jim Yergins (forum member) approx. 2 years ago, thanks again!
494 downloads
0 comments
Updated
-
Heater Model 504 Installation Instructions.pdf
By P15-D24
Factory installation instructions for Fresh Air heater for B Series trucks.
149 downloads
0 comments
Submitted
-
Windshield_Wiper Gaskets (1).pdf
By P15-D24
Windshield Wiper Gaskets template posted by HanksB3B
80 downloads
0 comments
Submitted
-
Vacuum gauge chart
By Alshere59
A basic chart that gives typical readings for trouble shooting.
120 downloads
0 comments
Updated
-
0 comments
Updated
-
Fuel pump heat shield template
By TodFitch
Dimensioned drawing of fuel pump heat shield.
239 downloads
Updated
-
radio_noise_suppression.pdf
By P15-D24
Set of instructions for installing radio noise suppression devices.
50 downloads
- radio
- radio noise
- (and 1 more)
0 comments
Submitted
-
Fenton Header installation instructions
By Alshere59
Installation instructions for the original Fenton headers. May help others with headers for pipe layout but a cross over pipe would be required.
79 downloads
0 comments
Updated
-
0 comments
Updated
-
BW_OD_Info.pdf.zip
Instruction manual for BW overdrive .
103 downloads
- Reference
- over drive
- (and 1 more)
0 comments
Updated
-
0 comments
Submitted
-
Fulton Sun Visor.pdf
Comprehensive Data and Directions for Assembling, Painting and Installing FULTON SUN SHIELD
138 downloads
0 comments
Updated
-
Flashing/Polarizing Generator guide
By Alshere59
Polarization restores the residual magnetism in the cores of the generator field poles so that when the generator starts charging it will do so in the proper polarity.
It is usually not necessary to re-polarize unless the generator has been removed and repaired or the regulator has been changed. If this has occured, then re-polarization should be done before starting the engine. Otherwise, the generator may not charge or it could charge in the reverse direction.
Re-polarizing is relatively easy to do. All that is necessary is to briefly connect the generator armature to the battery hot terminal. The most convenient way to do this is to take a short jumper wire and touch it to the "Batt" and "Gen" terminals on the voltage regulator. At the moment of contact you should see a slight spark. This indicates that the process is completed.
It should be noted that it is the generator that is being polarized, not the regulator.
97 downloads
- Charging
- Electrical
- (and 1 more)
0 comments
Updated
-
0 comments
Updated
-
Updated
-
Radiator Seal
Factory P15 front radiator seal to improve air flow through the radiator.
84 downloads
0 comments
Updated
-
Mopar Factory PCV System
Mopar Factory PCV System how to.
2,143 downloads
- Mopar Factory PCV System
- Engine
- (and 3 more)
Updated