Jeff Balazs Posted January 15, 2014 Report Posted January 15, 2014 Does anyone have any size information on the data plate that is supposed to be affixed to the door pillar? Mine is missing and the one I ordered from VPW is too wide. A photo would be great. Thanks, Jeff Quote
ggdad1951 Posted January 15, 2014 Report Posted January 15, 2014 Mine from vow was identical in size to my original Quote
Larry Leibhart Posted January 15, 2014 Report Posted January 15, 2014 Original Data Plate 1 11/16 in. wide by 5 13/16 in. long Quote
Jeff Balazs Posted January 16, 2014 Author Report Posted January 16, 2014 Hmmm? that is what they sent me.....but it doesn't look like it will work. There is a recessed area in the pillar that it should sit flat in and it is only about an inch wide. Not sure what to make of this. Jeff Quote
ggdad1951 Posted January 16, 2014 Report Posted January 16, 2014 Mine had a slight bend in it to fit Quote
Dodgeb4ya Posted January 16, 2014 Report Posted January 16, 2014 The factory data plates are slightly dished lengthwise to fit the curve of the pillar. Quote
Jeff Balazs Posted January 16, 2014 Author Report Posted January 16, 2014 Ok Thank you.......it just did not look right. Does anyone know what size stamp was used to letter these? Jeff Quote
ggdad1951 Posted January 16, 2014 Report Posted January 16, 2014 (edited) I think for mine it was a 5/32". I'd have to look at home or try and find the thread I had on it here. Or send it to me with all the info and I'll stamp it and bring it along to the BBQ Edited January 16, 2014 by ggdad1951 Quote
Barry Maxwell Posted January 16, 2014 Report Posted January 16, 2014 Jeff: The data plate on my '51B3C is 1-5/8" by 5-3/4' and it is original. If I have done it correctly there should be a photo attached. Barry Quote
Jeff Balazs Posted January 19, 2014 Author Report Posted January 19, 2014 Thanks guys. Ok I guess I have the correct item. Just need to stamp the numbers and then dish it in to conform. I need to get this done as the VIN has to appear in two places in order to get title and registration here. Thanks, Jeff Quote
HanksB3B Posted January 21, 2014 Report Posted January 21, 2014 (edited) Thanks guys. Ok I guess I have the correct item. Just need to stamp the numbers and then dish it in to conform. I need to get this done as the VIN has to appear in two places in order to get title and registration here. Thanks, Jeff Good job Jeff the other place you know is stamped into the front driver's side of the frame. Unfortunately I didn't know this and failed to affix that plate on mine. The DMW (dumb man walking) would not let me go home and return with my plate on the cab. I ended up with a DMV "assigned number" which included riveting a plate on my door frame and one on the frame. Grr, Hank Edited January 21, 2014 by HanksB3B Quote
Jeff Balazs Posted January 21, 2014 Author Report Posted January 21, 2014 Sounds about right. Jeff Quote
ggdad1951 Posted January 26, 2014 Report Posted January 26, 2014 Just make sure when you punch the numbers you back it with a solid material or it will draw deep Quote
Jeff Balazs Posted January 26, 2014 Author Report Posted January 26, 2014 Just make sure when you punch the numbers you back it with a solid material or it will draw deep Yes I did......came out just fine. Jeff Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.