Instructions, Manuals & Templates
Instructions sheets, manuals and templates for missing parts.
100 files
-
D-24 Gauge Cluster Gasket Template
By Conn47D24
This paper gasket sits in the back of the main gauge housing, and the gauges install OVER the gasket from the rear of this housing.
I have taken apart two sets of gauges and the paper is always dry, and flakes off.
Enjoy !
4 downloads
Updated
-
Comfort Master 54 (Driver side) Heater Repair Kit
By Conn47D24
Another cool piece of history of our cars saved. Enjoy !
44 downloads
0 comments
Updated
-
Heater - Water Valve Instructions " Y " Type
By Conn47D24
Copy of original installation instructions that came with the NOS " Rabbit Ear " or " Y " valve.
60 downloads
0 comments
Updated
-
Trouble Shooting in the Transmission.pdf
By P15-D24
3 speed manual transmission trouble shooting guide, Mopar factory service reference book.
129 downloads
0 comments
Submitted
-
TrackingDownTIreWear.pdf
By P15-D24
Mopar Service Reference Book "Tracking Down Tire Wear"
22 downloads
0 comments
Submitted
-
Power Steering.pdf
By P15-D24
Step by step instruction for adding to power steering to a Desoto sedan, authored by Donald J. Smith. Detailed instructions how he modified and added power steering to his 4 door Desoto sedan. The .zip file contains the individual photos used in the article.
211 downloads
0 comments
Updated
-
1946-48 Trunk Light Installation Sheet
By Conn47D24
Bored on a snowy day. Organizing years of parts and found this to share.
Trunk light sheet from NOS box.
Mopar # 1232609 ( same as # 1244922 )
55 downloads
0 comments
Submitted
-
Hand Brake Signal Installation Intructions
By Conn47D24
Seems that this switch is readily available, however the complete accessory package is rarer and more expensive. here are the instructions should you have , or find just the switch.
Good luck
Conn47D24
D24 Hand Brake signal switch Instructions02032017.pdf
26 downloads
0 comments
Updated
-
Chrysler218.236.251Manual.Complete.Reduced_0.pdf
By P15-D24
Service manual for Chrysler Industrial Manuals.
204 downloads
0 comments
Submitted
-
0 comments
Submitted
-
DIAGNOSING THE HYDRAULICALLY OPERATED TRANSMISSION
By HotRodHerman
This is a copy of an original Service Reference Book from 1948 by Chrysler Corporation
37 downloads
0 comments
Submitted
-
THE HYDRAULICALLY OPERATED TRANSMISSION - HOW IT WORKS
By HotRodHerman
This is a copy of an original Service Reference Book from 1948 by Chrysler Corporation
26 downloads
0 comments
Submitted
-
1949 CHRYSLER INSTRUMENT CLUSTER GASKET
By rb1949
This is a PDF template for the one piece paper (fiber) gasket for the 4 gauges and odometer housing that mount to the rear of a 1949 Chrysler Instrument Cluster. I believe 1950 used the same cluster. Made to keep dirt, dust, etc. from getting into the gauges. Cut with a sharp instrument to avoid 'tearing' the material edges. Punch the screw holes slightly lager than the screw. Print the template at 100%.
30 downloads
0 comments
Submitted
-
Bellhousing to transmission gasket
By 48ply1stcar
I bought this gasket on Ebay and I will probably only use it as a pattern. The height if the gasket is 6 11/16" and with where marked is 6 7/8". I hope this is useful.
92 downloads
0 comments
Submitted
-
Submitted
-
Inner Fender to Frame Seal Template
By Conn47D24
This template can be used to trace and cut out the masticated rubber seals between the Front, INNER fenders, and the frame.
They are stapled on to each inner fenders ( driver and passenger ).
I was lucky to purchase both inner fenders NOS with the original rubber seals attached. I am sharing them here for your use. I have benefited from help here on other templates so I am paying it forward.
Instructions:
Purchase a sheet / roll of masticated rubber. 1/8 " thick min. ( like tire rubber with poly cord imbedded )
Print the templates on LEGAL size paper ( 8.5 " X 14 ")
Match the two pages where shown and tape the sheets together.
Cut out the template
Trace on to the rubber sheet ( bright color pen / marker )
Cut out the rubber seal.
I used heavy gauge stainless steel wire to make the " staples " and wired the seals to the inner fenders.
Note: my D24 is a Club Coupe, I believe the front fenders are the same on other Models and maybe Chysler's other lines.
Good Luck !
Clay Janer
Conn47D24
173 downloads
0 comments
Updated
-
1947 Owner’s Manual Mopar Radio Model 802 Plymouth Dodge DeSoto Chrysler
By linus6948
1947 Owner’s Manual Mopar Radio Model 802 Plymouth Dodge DeSoto Chrysler
Sorry for the upside down scans
321 downloads
0 comments
Submitted
-
0 comments
Submitted
-
Mopar Steering Tie Rod End Service Packages.jpg
By P15-D24
Installation instructions for tie rod service package.
81 downloads
0 comments
Submitted
-
SHIFTRITE PAGE 1a.jpg
By Mark D
Manufacturers installation brochure for the Shift Rite column mounted overdrive control.
153 downloads
0 comments
Updated
-
Edmunds Install Instructions.jpg
By P15-D24
Edmunds Install Instructions for Chrysler, DeSoto, Dodge and Plymouth 6 Dual Intake Manifold
143 downloads
- Dual Intake
- Edmunds
- (and 1 more)
0 comments
Updated
-
0 comments
Submitted
-
0 comments
Submitted
-
0 comments
Submitted
-
Flathead 6 Engine Rebuild.pdf
By Mark D
Four Part Auto Restorers Magazine article which describes the Flathead 6 teardown and rebuild completed by the author Curt McConnell. 21 pages - pdf format.
607 downloads
Submitted