JBNeal

VINTAGEPIC: saw this B-3 long bed on the FB

as The Black Knight infamously said, TIS BUT A SCRATCH...that'll buff out 😁

Here is the wiper switch with the knob and bezel removed. The bezel screws onto the switch body threaded shaft; the knob presses onto the switch split smooth shaft. Pictured is the small screwdriver blade that I used to pry that knob off of that smooth shaft, as it is a tight fit that gets tighter when dirt accumulates up in there. Ya might need to wiggle this knob back and forth while prying upwards, but don't get in a big hurry or go all HULK SMASH on this knob as it is pot metal...the first knob that I tried to pry off back in the 90s crumbled to chunks 👀

Maybe Dodge realized that it was a problem in preproduction so it was mandated that the heater option was dealer installed...I've worked with at least one OEM that knew when to kick the can down the road...if'n ya had the fresh air package installed, you'd definitely be taking things apart to adjust them valves

I am all for exploring the solar system, but I'm kinda wondering how come traveling on this planet has not been completely conquered yet...Arctic and Antarctic trips are still considered treacherous and too arduous...that kinda technology might transfer to transiting lunar or martian landscapes...how'bout making traveling to the poles a priority over lunar golfing expeditions 🤔

Before the advent of zinc plated hardware, I reckon that the engineers relied upon nature's thread lock: iron oxide. For this low torque application, I'd be leaning towards flattening some threads with pliers or a hammer + punch, cuz how often is cab mounting hardware going to need removing...then again, I've recently seen pics on the internets of oil drain plugs tacked to the pan, sometimes jokesters leave surprises for the next guy 👀

yep

Looks like some good progress here...I see enough dry valve lifter surfaces to confirm that valve train is locking up the engine. I have seen valve lifter areas coated with sludge, so much that it had to be scooped out. Them flakes looked like dried up oil. Overall, this valve lifter area looks OK, could be a lot worse. Now you can see what more needs to be soaked with penetrants. If them valve springs have pits or other corrosion, they'll probably need replacing at some point. •The manifold studs penetrate the water jacket, so coolant loss here during disassembly is normal. •That puddle of water near the draft tube could be condensation, as that area is right next to the outside air. •Beware: that valve area sludge may have lead in it. additional information - heat riser advisor additional information - draft tube to partial PCV conversion

watch out for this'n on the intake manifold...it'll getcha 👀

Compare this excerpt from the C-1 shop manual to the B-3 shop manual...kinda looks like finger tight + 1/8 to 1/4 turn I reckon

the spacious interior of a Tucker

VINTAGEPIC: saw this B-1or2 on the FB

When I rewired the barn in 2019, I opted to go with 75W equiv. LED floodlamps as the price for GEs had dropped to about 5 bucks apiece. Before I got too carried away, I hung one in the middle of one of the bays and disconnected the existing lights and did a test one night to determine its pattern. The next day, I hung another so there was some overlap and verified the results that night to see how hard it was to read the label on the LED box...made an adjustment the next day, tested it that night, then a second adjustment was verified the night after that. From there, I figured the light spacing required to fill the whole barn and not have shadows in the corners nor have too much light overlap and waste $$$ on hardware. The best part is heading out to the barn in pitch black night and hitting the lights and it not feel like a flashbulb just went off in my face. Several of the neighbors have this problem as the electricians they hired to do their barns were of the mindset that if some is good, more must be better, so they put in lights that are too big and too close together and too many of them and charged too much for their work...it's like standing on a snow-covered field on a sunny day in there, almost migraine inducing

My samesung has android op.sys, and I can go to the picture gallery, tap on a picture to view, hit the pencil icon to edit the picture, and there's a 3dot menu at the upper right that pops up that when tapped, gives me the option to resize... once I choose a lower resolution, I can save as a copy any changes...if I want to undo these changes, the edit function can be tapped and the option to revert to original is available if I accidentally save the edited picture instead of saving the changes as a copy. Once I figured this out, I could post pics directly from my phone or tablet without having to transfer to my laptop for editing and posting...this is a nice time-saving feature when my laptop is several counties away

VINTAGEPIC: spotted this B-series Panel on the FB

additional information - inner fender removal From the factory photos that I've seen in Bunn's books and my experience with OEM assembly work, more than likely the assembly line had alignment jigs on the ready at each stage of assembly. We just have to get our single projects done and not truck after truck after truck like they did on the line...so the best approach is to kinda sit the big pieces in place on a best guess, then adjust as needed until we feel it's close enough, then start torquing everything down and hope for the best while checking sheet metal fit. I should clarify that my suggestion is to set the inner fenders in place and maybe start 2 or 3 bolts on the fender ends. If the inner fenders are blocking access to something, they can propped up out of the way without complete removal from the engine compartment.

I vote for getting them inner fender parts in place before tightening everything since you've got a li'l wiggle room now. When them fenders are bolted down, reinstalling them big panels requires some finagling, some scraping, and some colorful phraseology 💥

I found the FB listing in question and this picture has some details worth expanding upon. Original color probably is that white hue on the firewall...if the back of the glovebox door is the same color, then more than likely that was the original paint. The heater core appears to be aftermarket and the hacked appearance of installation and disuse is not a good thing...it's not a deal breaker as it's peripheral to the engine and can be addressed. That carburetor looks cleaner than anything in the engine compartment, so maybe that's recent. The head bolts have been changed to studs with chrome cap acorn nuts, maybe the engine has been gone through, maybe not. The missing rad.cap bothers me, that's easy enough to replace but that chore has been neglected. That plastic fuel filter dangling in proximity to the exhaust manifold really bothers me, kinda tells me the engine has been re-fired after years of being dormant and the owner has lost interest and needs to pay bills before January...who knows what jive he's pushing to unload this beast. The engine number is stamped on the block, and casting dates can be found on the block and head, directly above and below the distributor. A build card would need to be procured to determine if the engine was original to the truck...a shortcut might be that if the truck title number and flathead engine number are the same, then maybe that flathead is original. Modern VINs didn't appear until nearly two decades after this truck was manufactured, so the engine number was used on many titling documents...which can be a problem as back in the day there was a legitimate business in engine rebuilding and replacement to maintain vehicles longer rather than buying new vehicles. These flathead engines from 1951 onwards were basically the same, with changes in compression achieved by head machining. Parts availability should not be an issue though more expensive than blue oval or gm of that era as Dodge accounted for something like 10% of the truck market back then, so Dodges are rare compared to them. The side-mounted spare was not a factory option until 1957 or so, definitely not on a C-1, but there were aftermarket kits available as well as many homemade versions found in the wild. That spare was originally underslung of the bed, out of the way. This truck looks to be a good candidate for restoration, but missing pieces, quick (sloppy) mods and its deteriorated condition are not causing me to drool over it. If there's no title available right now, I would be even less interested. If'n ya showed up with a trailer and 3k in unmarked bills in a paper bag, maybe that could close a deal, but more than 5k price tag is a deal that I'd pass on...these guys want top dollar from somebody who is running on emotion and don't like to haggle with someone armed with knowledge. I like to save a relic from the past from an unfortunate fate, but I don't wanna end up in the poor house reviving a basketcase