JJs 1948

Will the transmission in the 1939 bolt to the 250?

Thank you for the response's gentlemen. I am trying to be neutral on this question. The 250 engine is one I own and is fully rebuilt. I never used it and don't need it anymore. I met the owner of the 39 Plymouth at a car/truck show this summer and he wants to know if it would work in his 39. He'd like to use the 250 engine since it is already rebuilt. Any other ideas would be appreciated.

A friend of mine owns a 1939 Plymouth PT81 with a worn out 201 engine in it. He can get a rebuilt 250 engine from a 48 Chrysler car. Is it possible to swap them using the 39 transmission. The 250 does not have a trans with it. Is it possible to move the radiator forward and use the 250 front motor mount? We would appreciate information from anyone that may have done this. Thanks

I found the easiest solution for vapor lock was just hold the gas pedal to the floor and push the starter pedal with your left foot. Starts right up everytime after very quick.. I always worried about taking my truck out, even for a casual drive, and now I don't worry about it one bit. So many people make this such a difficult problem when actually it's a simple fix. I do have a heat shield installed on my engine but they don't prevent vapor lock. Try it out. Jeff E.

The part you are looking for is called a "cowl seal". I bought some through www.dennis-carpenter.com. The seal he sells is just like the original and really looks and fits well. Go to his website and search for part # 7C-16068. They sell this seal to be used for Ford trucks from 1948-52 but it's also the same material that Dodge used. I hope I can post a picture but having a very hard time with this new forum. Use this part! I have a pair from Roberts that I did not use. Good Luck.

Here is a Jiffy Jet Windshield Washer on my 48 B-1-B. I bought it from Reg Evans. Mostly complete but found everything else needed on eBay. I need to brush up on learning how to post messages and photos again. It's been awhile since my last post. I'll try to put a few more photos of accessoryies that I have on my truck if this post works. Jeff

I used the rubber door strip for 48-53 Dodge Truck from clestersauto.com and it worked very well. They do sell just the door strips and not part of another larger kit. No nails, screws, or tacks, just glued it on. Jeff

Barry, The frame is the same from 1948 thru 1951 from everything I have seen here on the forum and the photo of Merle's truck. I'll get the parts out to you next week. I have an out of town wedding to go to this weekend. Once you get the parts you will see how the bumper attaches to the frame. Send a measurement if you want but I should have a pretty good sense of where to cut the pieces off at. I will leave you plenty of metal to work with and keep the shipping cost down too. Should be fine so don't lose anymore sleep. Jeff

OK Barry. I'll get the frame parts off next week and shipped to you. Jeff

I have a 1948 B-1-B parts truck that I am going to cut up and scrap out. If you want the front frame rails I can send them to you. If you want them, give me the size and they will only cost you the shipping. Jeff

In Michigan the Ethanol lobby is pushing for a 20% ethanol fuel mixture. This proposal concerns me very much being a Marathon Gas Station owner for the last 19+ years. Much of my fuel dispensing equipment will have to be changed or replaced and the mainenance costs will increase substantially. To sell E-85 fuel takes a complete fuel system to dispence that fuel to the customer.

Very nice video Merle. Awhile back I posted a thread on adjusting valves while the engine was running. In my case I was the onlooker while my mechanic friend did the adjustment. Turns out the job is easier than one might expect and is "THE" way to adjust valves on these old flatheads. One of the most important steps to do and which my friend stressed the most was to slow the engine idle speed as slow as possible. I swear with the engine running so slow you could adjust and actually hear the difference in the smoothness of the idle as each valve was adjusted to correct gap. Amazing difference in the overall performance of my engine. I had such an improvement that my truck seemed to get one more gear of top end. I can travel at 55-60 without a problem with a 3.73 rear end. Remember to let the engine warm up completely too. No knuckle burns and we bent the end of our feeler gauge at an angle to avoid the manifold.

Hank, Do you still need an oil cap? I have an extra for you no charge. Let me know, Jeff

Here are a couple photos of the washer on my truck. Purchased it from Reg. I would be glad to answer any questions. Photo 1 & 2 show the washer jets are in the chrome piece below the windshield divider. Two jets in that piece spray to each side of the windshield. Photo 2 & 3 shows the pump which seemed like the best location that I could figure out but a more experienced member here may know the exact way a dealer would have installed it. One thing I need to do is relocate the foot pump between the clutch and brake pedal as the directions show. See last photo, and I forgot to put the round disc pedal on the foot pump stem in that picture. Hope this helps. Good luck. Jeff

Thanks Reg. Which mounting bracket is for the Dodge Trucks? I believe I have the correct smaller horn but would like to see how they were mounted. Thanks again, Jeff Any other photos or factory illustrations would be greatly appreciated from anybody.