Jump to content

52cambridge

Members
 View Profile  See their activity

  • Posts

    20

  • Joined

  • Last visited

 Content Type 

Everything posted by 52cambridge

  1. 52cambridge
    I took moose's advice and made my own using grade 8, 3/8" x 2.5 in. bolt and 2 bronze 3/8" flange bearings. Put in new pins and washers. Works like new. Shifting is much more precise and tight. Robert KB, I will give you the dimensions of the shoulder bolt. I still want the original part. Thanks again for everyone's help and advice.
  2. 52cambridge
    The diameter of the shoulder is 9/16". Andy could not help me without a part number. I went to a fastener supply co. They did not make one in that size. Its a hard to find special order part that will cost big. I am going to try to make my own. If that fails, I will go one size up and have it machined. Thanks for all the help everyone!
  3. 52cambridge
    I have a 52 Cambridge and broke the bolt that holds the shift linkage arm to the frame. Where can I find one?
  4. 52cambridge
    Very nice ride. Couple of questions. What size steelies are you running? Did you lower the front end? If so, did you cut the springs or use drop spindle kit?
  5. 52cambridge
    beautiful!!!!!
  6. 52cambridge
    Very nice work! How did you learn to weld? Were you taught or was it trial by error/learn on your own?
  7. 52cambridge
    Yea, he really comes off as curt and arrogant sometimes. Nice way to conduct business! LOL
  8. 52cambridge
    Anyone out there have an ignition assembly with key for a 51-52 Plymouth?
  9. 52cambridge
    Ok, got it apart, but broke copper tab that wire gets soldered to. PITA! is right. I quess I just bought a new one. Thanks for the info through.
  10. 52cambridge
    I am trying to replace the ignition wire that runs through the steel cable on the assembly. However, it appears that the ignition switch is a sealed unit. Is this the case?
  11. 52cambridge
    Thanks, I wasn't aware. Yea I'll be there!
  12. 52cambridge
    flathead 6? Yes of course. I'm sorry, but I don't follow you. Where should I stand corrected? By the way Blueskies, I am a huge fan of your car and your website. I've learned alot from your detailed records of your project. You are one of the reasons why I plan to keep this car a flathead from seeing your video clips on how well these cars run at highway speeds with an overdrive.
  13. 52cambridge
    Drivetrain is stock 230 SBC with stock exhaust manifold with split Y pipe and dual glasspacks. I plan to remove the Y and connect up to dual manifolds and dual carbs when I rebuild the engine. Here are some a/v clips.
  14. 52cambridge
    If you were to guess, How much HP/Torque do you expect to get?
  15. 52cambridge
    Thanks, That dash looks real clean. Nice job!
  16. 52cambridge
    Trying to work out some electrical issues. What do the indicators in the picture represent?
  17. 52cambridge
    Took it for a spin. Wow! what a difference. So smooth!!! I recommend.
  18. 52cambridge
    Just installed new driveshaft with modern u Joints. Total cost $350 from A-1 Drive Shaft Company in Baltimore MD. I dropped my old one off yesterday and got new one 2 hours ago. Runs smooth on jacks stands. Attempted to rebuild old one. Ripped new boot while trying to install. Parts for total rebuild of old shaft were going to be $160-$350.
  19. 52cambridge
    I wonder if you could run more than one power inverter. Say, one for the radio and one for accessories?
  20. 52cambridge
    Listen to the exhaust on this 52. I am going to get the same setup after hearing this. Start clip at 2:30
×
×
  • Create New...

Important Information

We have placed cookies on your device to help make this website better. You can adjust your cookie settings, otherwise we'll assume you're okay to continue.

Terms of Use