weasel
-
Posts
45 -
Joined
-
Last visited
-
Days Won
1
Content Type
Links Directory
Profiles
Articles
Forums
Downloads
Store
Gallery
Blogs
Events
Everything posted by weasel
-
FOR YOUR INFORMATION,I DID SEARCH WITHOUT ANY LUCK. MAYBE WHEN YOU ARE 70 YEARS OLD YOU MAY NOT BE AS SMART AS YOU SOUND Thanks for all the help
-
Is there a year of tranny that will fit without changing the output shaft? Do you know who sales the kit?
-
Does anyone sale a bell housing that converts a T5 to a stock 218 block? Is there a year of tranny that will fit without changing the output shaft?
-
Headers or stock exhaust manifold
weasel replied to Dennis46PU's topic in Mopar Flathead Truck Forum
I have a stock exhaust from a 49 b1 218 23". I will sell it for 100.00 you pay shipping. -
49 1 My terminals are located on the radiator support as well. David
-
Wayfarer Thanks for the reply, this is very helpful Dave
-
Has anyone used a long bed Dakota on 49 B1.
-
Can someone help me with Torque Specs. for the Rear Nut on the rear pinion for my 49 B1 1/2 ton? Also can I replace the rear seal without having to put in a new crush seal? Thanks David
-
Thanks for the reply, I have it in the air now and will remove the floor plan. David
-
I need to pull the three speed out of my 49 B1, my question is can it be done without pulling the top cap from the tranny? I don't have a lift so I will be using jack stands? Thanks for any guidance
-
This is my 49 b1, have been working on it for two years.
-
Thanks Mike that is what I needed to know.
-
Is it possible to remove the steering box column etc. without removing the floor panels? I have read a lot of posts but haven't found one that specifically says. If anyone has done one of these I would appreciate the help.
-
Has anyone replaced the stock steering box with a new one? My is worn out has to be swapped.
-
It is a floor shifter. What could cause it to pop out of gear? the 3 speed? Has correct fluid level.
-
My three speed is flying out of gear. Third gear
-
I have a 49 B1 with a three speed in the floor shift. I found a 4 speed floor shift that I would like to change out. I don't have the three speed out so I can't expect the shafts etc. The four speed has a date on the top of 1-21-48, the Id number is C-39871 on the top plate. The number on the main case is C88661. Does anyone know if this swap will work? Are the input and out put shafts the same Etc. Thanks Dave
-
It is a couple inches before you feel any pressure.
-
It is a floor shift. The clutch starts engaging about 1 1/2 " off the floor.
-
Finally got my 49 B1 on the road , now its is flying out of third gear. Any suggestions?
-
THANKS FOR THE INPUT.
-
Where can you send a steering box to have it rebuilt? cost? Thanks David
-
The picture is different than the wheel in my b1. One end of my big spring is open the other end has metal cap.{with hole} Does the open end sit on the horn ring hold down plate? After getting the wire through the steering tube, do you then press the locking plate into the steering wheel plate a turn it until snaps in place. I'm lost after that point? The kit I got also has a wire ring? May go into slots in bottom of horn button? Also does the steering tube have a metal cap on it to hold the steering shaft in the center of the tube. This was all apart when I got my truck so its very confusing to me?
-
Thanks for the reply. I guess I will be changing to volt meter ,I sure don't want to see my truck go up in smoke. I found a auto meter volt mini meter that will fit into the old gauge housing with a little mod. work to the housing.
