Jump to content

"Ran When Parked" 1954 Dodge C 3/4 Ton


DrFate77

Recommended Posts

I'd been meaning to get a thread started for our project, this site has truly been a huge resource for me so far.

 

We're about a year in working on grandpa's '54 Dodge pickup - I think the VIN has it as a C-1-C 3/4 ton. He was the second owner, the first being the local mailman. Grandpa bought it from him in '56 and used it as a farm truck on his western Kansas farm, partly to haul sheep to the sale barn. He quit driving it after he got a new truck in the '70s sometime, and it had been parked out behind a shed ever since. I don't think the truck has ever moved under its own power in my lifetime, but grandpa swears it was running when he parked it last. My brothers and I used to play around on it when we were kids and I always thought it would be cool to restore. I finally asked him if he'd sell it to me to try to fix up, but he said I could just take it on the condition that I don't bring it back to him. lol. So two Thankgiving's ago, I borrowed a trailer to haul it back home and start in on it.  It was a job getting it unstuck and loaded, it was buried in mud up to the axles and did not come easy. Here's a video for your entertainment. https://youtu.be/R6dHknzmZR8

 

Most of the last year has been spent getting it tore down and cleaned up, I'll post a few more pictures here to bring us up to today. 

01.jpg

03.jpg

04.jpg

  • Like 7
Link to comment
Share on other sites

Wish the video wasn't private.?

Link to comment
Share on other sites

Coulda used the tractor to pull it up instead of the come along...been there done that (both ways)...that's a LOT of ratcheting!  :D

 

Looks good, can't wait to see what you do with it!

Link to comment
Share on other sites

great looking truck!  I had a similar experience with my B3F, although it took a come-a-long plust a small 542B(gas) Bobcat skid loader to load it...even with fully aired tires!

Link to comment
Share on other sites

Hey all, thanks for the comments. There probably was an easier way we could have loaded it, lol. I remember we had a hard time getting it to track straight up the ramps and on to the trailer. With the tires in shreds it took a lot of rewinding and fussing to get pulled up squarely. We were all working on it well after dark with the cold wind howling, which made it feel sort of like grave robbery. 

I think the patina's great even though it's not very even. The side facing the field got stripped mostly bare over the years while the shed side of the truck is actually pretty nicely preserved. All things considered, it's in good shape for sitting outside so long. We're doing disc brakes and rebuilding the engine, new glass, etc but I'm going to keep the rest as stock as possible. The body is covered in dents, welds, and years of farm fixes so I'm inclined to leave it with as much character as we can get away with. 

First thing was getting it cleaned up, and then found a nice day in February to get the engine pulled. I thought about trying to rebuild the engine myself, but realized the truck would never get finished that way. So we loaded up the engine and sent it to the garage my brother works at to get that part done.

IMG_1251.JPG

IMG_1627 (1).jpg

IMG_1608 (1).jpg

IMG_1648 (1).jpg

IMG_1658 (1).jpg

IMG_1853.jpg

  • Like 2
Link to comment
Share on other sites

Scope creep set in shortly after getting the engine sent off. The goal was to get the frame cleaned up and painted while it was relatively easy to get to. So the cab, bed, and running boards came off, along with steering column, pedal linkages, brake lines, and what was left of the wiring after the field mice got through with it. Then we realized the spring u-bolts and shackles were in bad shape so we went ahead and took the axles and springs off too. IMG_2731.jpg.44773e7beb3b2c7ad68cd565d984973e.jpg

 

IMG_3242.jpg.79f26b2dba70e10fe81d3c3d57fd42a1.jpg

 

IMG_3254.jpg.ce8bb7803a68d0c90fc8d7e3e88e7a37.jpg

 

IMG_3317.jpg.48e024de4952406347fd4ec5cbad3136.jpg

 

The gas tank and radiator are beyond repair. Not sure what to do about the radiator yet, but I got into the idea of moving the gas tank under the bed so I ordered a '70 Mustang tank from Rock Auto. The fitment seems like it'll do the trick, hopefully soon I can get around to getting mounts fabbed up for it. 

 

IMG_3805.jpg.4224aebdc9f4266367ec9d61d0a95914.jpg

 

IMG_3806.jpg.26dc6b5a3b535ff017c3bfd1d946d20d.jpg

 

At some point I was left with just the frame on sawhorses, and I spent a few months with a wire wheel and electric pressure washer cleaning it up in the driveway. Right as cold weather hit, we got it moved inside to brush on a few coats of Eastwood's chassis paint. Those fumes were gnarly, huge credit to my very patient fiancé for putting up with that smell. 

IMG_4162.jpg.de7a3f6806a856fa09ea905d954e04ac.jpg

 

IMG_4166.jpg.54110151016c783987cbcbf10a5a2a3a.jpg

 

IMG_4342.jpg.41af938607ac0ed605fcd67c712e8dd7.jpg

 

IMG_4447.jpg.033fe3cdc2a3f6a79d66abea70321aa4.jpg

  • Like 3
Link to comment
Share on other sites

You're being very ambitious but that is a good thing. You'll love it all the more when it's finally done and driveable. That old girl was stuck pretty deep into the ground so I am not surprised there were issues with shackles, spring, axles, etc. Good luck with the project and keep the pictures coming as we all like pictures!

  • Like 1
Link to comment
Share on other sites

On 1/10/2021 at 12:30 AM, DrFate77 said:

Thanks for the tip about the headlights. I dropped the doghouse off with a friend to get some bad cracks welded but as soon as I get it back I can start thinking about what to do with that part. 

I was going to do that conversion, even have all the parts...then ran across some NOS ones....much easier!  LOL

Link to comment
Share on other sites

Just wrapped up the rear axle, getting that figured out has taken up most of this winter so far. The original plan was to reuse the stock rear axle and drum brakes, but when we tried to pull off the drums we managed to crack one of them straight through. At that point, getting a newer axle with disc brakes started to make more sense dollar wise than replacing and rebuilding drums. 

 

Pick-N-Pull had a few '90s Grand Cherokees, this '96 Laredo had the least amount of rust on it. The number plate is illegible but it would have had a Dana D44A axle, with a 3.73 ratio?  Took two trips for us to get it removed. 

 

01.jpg.433961fae0ca472c588741bbcae0cc68.jpg

 

02.jpg.d8ee4c29f50f899e259a7d13d90c15fc.jpg

 

03.jpg.06d4f9b13b78baa44edcdca9e2a42128.jpg

 

The folks on this site were right, Grand Cherokee rear axle dimensions are more or less spot on with stock and the driveshaft bolts right up. The GC axle is 5 x 4.5 vs the 3/4 ton's stock 5 x 5 bolt pattern, but that's not a big deal for us. My stock wheels are rusted through and unsafe so I'll be looking for different wheels at some point anyway. 

 

04.jpg.cdc38b6edc3a6c476542e49fb3e8f053.jpg

 

05.jpg.b2e59cc3c0af4170dff6cf093ae7d8d9.jpg

 

A half dozen cutting and grinding wheels later and all the stock brackets were gone. 

 

06.jpg.632c5d3ee65143e125044e430e696026.jpg

 

07.jpg.ea740c3c62cc81ee9aab1f8da9261035.jpg


My dad is a retired architect, so I brought him in to check us on the perch geometry. We leveled the trailer we were using to work on, put the stock axle on jack stands, raised the front until the perches were level, and got the drop-down measurement from where the driveshaft connects. Then we put the new axle in its place, matched the dropdown, and clamped down the perches level at the right width from center. 

 

09.jpg.c2bfc3d6dc18324255a0efb1de2c3f57.jpg

 

10.jpg.0473569411311e575caf627a74a5a8d0.jpg

 

Tractor Supply's weld-on trailer perches are a good equivalent. My brother knocked out the welding. Doesn't have to be pretty as long as it holds!

 

11.jpg.6a3d127b6d0c1bbd5b0d42e282498c00.jpg

 

12.jpg.ab189fc90cb8c32a6d5b180c26367c58.jpg

 

Then finished cleaning it up and drained the oil. We also took the opportunity to unpin the axle shafts and replace the seals while we were in there. 

 

14.jpg.90cd25105bd5c1d0d5b839a833e59e43.jpg

 

Then painted it with black chassis paint, ordered new U-bolts, and reinstalled everything. 

 

16.jpg.61114b57ed47d4e592b96d064f73732e.jpg

 

15.jpg.eb9dd3750f36cd3f8588daa30bab53c2.jpg

 

  • Like 5
Link to comment
Share on other sites

It might be a good idea to put something other than cinder blocks under those jack stands.  They've been known to break, especially when on their side and even if only one breaks, it'll all come down and mess up that hard work you've put in, or you, if you're under it.

  • Like 1
Link to comment
Share on other sites

14 hours ago, Dave72dt said:

It might be a good idea to put something other than cinder blocks under those jack stands.  They've been known to break, especially when on their side and even if only one breaks, it'll all come down and mess up that hard work you've put in, or you, if you're under it.


Totally agree. Disaster waiting to happen, especially as more weight goes on. 

Link to comment
Share on other sites

Hey thanks. I could use some pro tips on the transmission. I scrubbed the outside and rinsed the sludge out of the inside with mineral spirits, now just trying to figure out what else ought to be done. The bearings spin smooth and seem to be in good shape. Are repro cork gaskets the way to go or can I get away with gasket paper and RTV? I'm going to use the Grand Cherokee parking brake, can the transmission brake drum be safely omitted? Appreciate any advice, transmissions aren't my specialty. 

IMG_4846.JPG

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
×
  • Create New...

Important Information

We have placed cookies on your device to help make this website better. You can adjust your cookie settings, otherwise we'll assume you're okay to continue.

Terms of Use