Jump to content

Remote oil filter options ?


Recommended Posts

Hi Gang;

I have been running the remote oil filter that came with my truck for 5 years. It is the type that takes the Baldwin sock type element. It is hung on the side of the block and shares one mounting hole with the spark plug loom. I would like to upgrade to something easier to service preferably with a spin on canister and mount it on the fire wall. Anybody out there done something like this and have any feedback?

Thanks in advance, Jeff

  • Like 1
Link to comment
Share on other sites

I put a spin on filter.  Used this mount https://www.amazon.com/WIX-Filters-24755-Filter-Mounting/dp/B0014BIAG0

and this WIX filter https://www.wixfilters.com/Lookup/Exactmatch.aspx?PartNo=51050

This is a by pass filter needed for these engines.  I did have to make a mounting bracket as you can see in this picture.  I am happy with this setup and is a lot less messy. 

 

spark plug wires.gif

  • Like 3
Link to comment
Share on other sites

Thanks for the info. That is the sort of thing I am after. I want to get it off the engine and perhaps mounted on the fire wall or fender. Are those flex lines you have on it?

The oil lines on the filter I have were hard lines and are it the way when removing the starter or soft plugs. I want to eliminate this situation and make other things easier to get to.

Jeff

  • Like 1
Link to comment
Share on other sites

On 5/6/2020 at 12:53 PM, tanda62 said:

I put a spin on filter.  Used this mount https://www.amazon.com/WIX-Filters-24755-Filter-Mounting/dp/B0014BIAG0

and this WIX filter https://www.wixfilters.com/Lookup/Exactmatch.aspx?PartNo=51050

This is a by pass filter needed for these engines.  I did have to make a mounting bracket as you can see in this picture.  I am happy with this setup and is a lot less messy. 

 

spark plug wires.gif

 

Not wanting to nitpick such a fine detailed piece of work here, but that crankcase filtered cap opening should be facing away from the radiator for the draft tube to work...if going with a PCV setup, the opening probably should be facing away from the radiator just to keep the bugs out of it :cool:

  • Like 1
  • Haha 1
Link to comment
Share on other sites

  • 2 weeks later...

I'm looking to do the same thing and thank you for the part numbers. 

 

My only question is which line goes where on the remote base.  I've used these remote filters before and they have had an arrow indicating the "in" ports.  Which line from the engine goes into the "in" port?   I don't know which is which on the engine itself.

 

Thanks!

 

Link to comment
Share on other sites

The best description I can give you is the upper is "IN" and the lower is "OUT"  of the filter. The mount has the "IN" on the left (towards the front of the truck) and the "OUT" on the right (towards the cab). This diagram shows it better than I can describe. Hope this helps.

 

Oh and your right JBNeal, when I took this picture I had added some oil and put the cap on backwards.  Fixed it before driving.  Always a good idea to double check your work not matter the detail! ?

 

oil filter.jpg

  • Like 1
Link to comment
Share on other sites

  • 3 years later...
On 5/6/2020 at 10:53 AM, tanda62 said:

I put a spin on filter.  Used this mount https://www.amazon.com/WIX-Filters-24755-Filter-Mounting/dp/B0014BIAG0

and this WIX filter https://www.wixfilters.com/Lookup/Exactmatch.aspx?PartNo=51050

This is a by pass filter needed for these engines.  I did have to make a mounting bracket as you can see in this picture.  I am happy with this setup and is a lot less messy. 

 

spark plug wires.gif

Hi, I’m a little late to this party, but I was wondering if this bypass filter is tee’d off of the existing filter, like a parallel circuit, or if it replaces the original filter completely? If it replaces the original filter completely, are there any issues with restricting the flow? 

Link to comment
Share on other sites

It replaces the original setup completely. This particular WIX filter is designed for a bypass system like the one in our trucks so no flow issues.

  • Like 2
Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
×
  • Create New...

Important Information

We have placed cookies on your device to help make this website better. You can adjust your cookie settings, otherwise we'll assume you're okay to continue.

Terms of Use