JSabah Posted September 8, 2019 Report Share Posted September 8, 2019 Below is my ignition switch pictures. You will notice the wire is damaged. I don’t see a way to replace just the wire (I have not tried taking it apart yet)....is it possible? I did a quick search on epay and don’t see anything that looks like what I have. If the wire can’t be changed, how much current runs thru this ( thinking I can save it with some heatshrink.... but would rather have the original wire appearance Quote Link to comment Share on other sites More sharing options...
JSabah Posted September 8, 2019 Author Report Share Posted September 8, 2019 Forgot to mention, I am converting from 6v to 12v Quote Link to comment Share on other sites More sharing options...
Los_Control Posted September 8, 2019 Report Share Posted September 8, 2019 13 minutes ago, JSabah said: Forgot to mention, I am converting from 6v to 12v Thing with 6 volt wiring, it is heavier and required to be so, for 6 volts. You can re-use all your 6 volt wiring when switching to 12 volt. I still think your wiring you posted can be replaced, but it is heavier then needed for 12 volt as is. Quote Link to comment Share on other sites More sharing options...
JSabah Posted September 8, 2019 Author Report Share Posted September 8, 2019 If I recall the wire seems to be fixed in the stiff sheath. Quote Link to comment Share on other sites More sharing options...
Dodgeb4ya Posted September 8, 2019 Report Share Posted September 8, 2019 It is possible to take apart...tough job though... Quote Link to comment Share on other sites More sharing options...
keithb7 Posted September 8, 2019 Report Share Posted September 8, 2019 Are you trying to preserve the stock look and parts? If not, cut the metal tube that covers the wire. I cut mine close to the back of the key switch. Remove the metal tube. Splice in a new piece of wire. It travels to the coil, correct? 1 Quote Link to comment Share on other sites More sharing options...
Andydodge Posted September 8, 2019 Report Share Posted September 8, 2019 I did hat Kieth is talking about when I built the 40 Dodge 45 yrs ago.........its 12 volts due to V8 etc and with a new piece of wire has worked fine since.........andyd Quote Link to comment Share on other sites More sharing options...
JSabah Posted September 8, 2019 Author Report Share Posted September 8, 2019 (edited) Yes tying to preserve as much as possible. I suppose I could cut it as you say, splice a new wire on and try to reinstall the sleeve wo that from the engine bay it looks correct - with the casing going through the old style grommet/holder. I’ve done something similar on another cars hood release cables- fixed the outer sheath with epoxy putty in an inconspicuous place. Worked great and still lasting. Just thought if it were easy to change the whole wire, it might be better than hanging a splice (even soldered) Yes i I believe it goes to the coil but that is from memory so I need to double check my pictures and a wiring diagram. Edited September 8, 2019 by JSabah Quote Link to comment Share on other sites More sharing options...
JSabah Posted September 8, 2019 Author Report Share Posted September 8, 2019 4 hours ago, Los_Control said: You can re-use all your 6 volt wiring when switching to 12 volt. I have completely new 6v harnesses as a lot of the old looked old and crispy. I’m sure under some of the old tape, I can find a nice piece. At the time I ordered the wiring there was a chance I was keeping the 6v system and knew I could use it for either. Only issues with the new harnesses - no bullet connectors and not sure yet if I need to change anything else (terminals, bulb holders etc) Quote Link to comment Share on other sites More sharing options...
keithb7 Posted September 8, 2019 Report Share Posted September 8, 2019 (edited) Sellers demand a premium price for replacement stock type ignition switches for these old Mopars. Especially the ones that mount to the rear of the coil in the firewall. A new replacement 6V coil is low priced. However won’t be able to accommodate the rear coil ignition switch wire mount. I can appreciate your desire to maintain stock. For others with a different plan, maybe a revived, drivable old Mopar on a budget, this works. Edited September 8, 2019 by keithb7 Quote Link to comment Share on other sites More sharing options...
georgeeb Posted June 19, 2021 Report Share Posted June 19, 2021 any tips on how your got the ignition swith out? my 49 plymouth ignition will not longer take a key, so I am trying to remove it. I took the screw out from the bottom, expecting it to slide out. ive tried twisting one way or the other, but it will not move. not sure what to do next. Quote Link to comment Share on other sites More sharing options...
maok Posted June 19, 2021 Report Share Posted June 19, 2021 There is a very good chance the insulation is broken mainly outside of the tube and a little just inside, there is no reason why you could not slip over some shrink wrap over the wire and keep using it. Quote Link to comment Share on other sites More sharing options...
keithb7 Posted June 19, 2021 Report Share Posted June 19, 2021 (edited) Here is my ‘38 ignition key tumbler. Push in the little sprung pin seen here. Slide lock out. Edited June 19, 2021 by keithb7 Quote Link to comment Share on other sites More sharing options...
JerseyHarold Posted June 19, 2021 Report Share Posted June 19, 2021 To my knowledge, the little pin can't be depressed if the switch is in the locked position. If you don't have a key, the cylinder can be picked so it turns and then you can depress the pin and remove the cylinder from the housing. Quote Link to comment Share on other sites More sharing options...
Plymouthy Adams Posted June 19, 2021 Report Share Posted June 19, 2021 6 minutes ago, JerseyHarold said: To my knowledge, the little pin can't be depressed if the switch is in the locked position. If you don't have a key, the cylinder can be picked so it turns and then you can depress the pin and remove the cylinder from the housing. that is correct...the inner cylinder must be turned a bit for the detent to align with the pin.... Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.