Jump to content

EPiX's 1942 Plymouth Coupe Resto


epix1718

Recommended Posts

  • 6 months later...

Oh gosh.. it's been a long time since I even posted this.  I've neglected the car to the corner of the garage until just last night where I got some motivation in me to go work on it.  In the mean we've acquired 2 more rescue bulldogs.

 

Fhv8s16.jpg

 

gPzhna3.jpg

 

I didn't do much but going to spend this entire weekend dedicated to working on it and HOPEFULLY fire it up.

 

Removed the plugs and added some Marvel Mystery Oil, while it soaked I took lots of reference photos, removed some very old age dried rubber hoses, removed antifreeze, and took off the spark plug wires as well as the cap. Under the cap was surprised to see that the rotor looked fairly "new". The plug wires are shot, they were extremely brittle. Oh, tried turning the engine over by hand, and it did so without issue :)

 

I still will need to work on the brakes and may need to find some help on that but if not I'll just go head on and figure it out with help from online.

 

I also now in my possession a new set of Coker 16" Bias-Ply White Wall tires.  

 

pX4tB0o.jpg

 

rhcu7PY.jpg

 

v9Tbg9I.jpg

 

The Trailblazer SS is also undergoing some more modifications :)

5Kthu6F.jpg

 

-Pete

Link to comment
Share on other sites

Worked on it some more last night and today. 

 

Last night did a preliminary flush of the cooling system.. simply just flushed it out using the garden hose for the radiator, heatercore, and engine block.. Only a bit of brownish liquid came out, most was green antifreeze.  I opened the petcock down near the oil fill/distributor cap but NOTHING would drain out there so not sure if that is either broken or clogged.  I turned it all the way left and all the way right and no difference.

 

Took off the wheels this morning and drove them up to the local tire shop to have the new Coker 6.00-16 tires and tubes installed.  While waiting on the tires ran to a couple auto parts stores to get some Autolite 303's, new heatercore hose, and a new 1-3/4" ID cylinder head to radiator hose.

Bought a kit online for spark plug wires but when they came the wires were way short so found some better looking cloth/laquer style wires and misc crimps so pulled up some YouTube videos on how to DIY.  I think they came out pretty nicely.. The kit I found was for an 8 cylinder (and cheaper than the 6 cylinder kit lol) so I'll have a couple extra wires as backup.  

 

pgpJpEX.jpg

 

xT0QCVz.jpg

 

CMZyA7l.jpg

  • Like 2
Link to comment
Share on other sites

Another small update.

 

Put the new radiator hose/heatercore hoses on last night along with some new clamps.

 

Called tire shop this morning and was told the white walls were ready so went and picked those up, came out really nice.  Going to paint the wheels carefully once I decide on a color for the car.  I went with the Coker Classic 6.00-16 Bias Ply, white wall radials for the 16" wheel seem hard to come by plus the cost is pretty crazy.  Got these tires for about $125/each, the local tire shop mounted/balanced/new tubes for $135 out the door, so in all about $635 total.  I won't be driving the car a lot, maybe few hundred miles per year so they should be fine for my needs.

 

zILlUBO.jpg

 

KsMsI8P.jpg

 

It's pretty cold today so just going to spend it inside organizing some parts.  

Link to comment
Share on other sites

Not a whole lot done today, called local O'Reilly Auto Store and asked if they turned drums, they said they do if I make an appointment as they only have one fellow that knows how to do the job.  Going to be doing that soon depending on if I need it or not, the drums are quite rusty.  

 

I'm a chemist by trade and have been wanting to try out rust removal via electrolysis for a while so this was a good opportunity to try it out.  Rigged up a makeshift operation from household items like kitty litter bucket, old motorcycle battery, random steel threaded rod, and old motorcycle battery connected to a battery charger/jumper cables and going to let it soak overnight.

 

Some before pictures of a rear drum:

yBr4sPR.jpg

 

nHga1Gd.jpg

 

Csf22PQ.jpg

 

Electrolysis setup

XPYWRRG.jpg

 

WCFV3bV.jpg

 

One hour update being submerged and active

CS7e0KA.jpg

 

Bonus picture of all 3 Bulldogs on the motorcycle from a fundraiser we went to last night.

UUbV9Z4.jpg

 

On Monday a friend offered to help me out with the brakes, so HOPEFULLY we can get started on those.. I'll need to make sure his choice of beer is available :)

 

 

Link to comment
Share on other sites

Had some friends able to make it over this evening, was able to work on the drum brakes front/rear.  Still need to put in the brake lines and replace the master cylinder.  Looking at the drums they don't need to be turned as the scratches look pretty minor.

 

Full driveway:

jlGSYjx.jpg

 

6pnDucE.jpg

 

New components installed :) The date is when I bought them (Dec 2015)

BwClcP1.jpg

 

8HxbuNA.jpg

 

Before AND after of rear drums after electrolysis, rust reformer coating, and finally a rust inhibitive paint.

yBr4sPR.jpg

 

JwvZgYN.jpg

 

Going to buy some 1/4" brake line this week and run new lines, along with cleaning up the front drums and backing plates.

Link to comment
Share on other sites

Nice work.

 

 I will say that if you are replacing brake hardlines that the new NiCopp alloy lines are a dream to work with.  Did my whole '37 with the stuff and it made the job so much easier.  

Link to comment
Share on other sites

Good info, I'll check them out!  Just researched it, and is a nice alternative especially here in the rust belt states.

 

Nice article on the advantages/disadvantages of Nickel-Copper alloy lines here:

https://oppositelock.kinja.com/the-truth-about-copper-brake-lines-1818499200

 

 

Link to comment
Share on other sites

Looking good!  The trick to getting these brakes after you get them reinstalled is to get if possible a Lockheed brake adjusting tool if not go to special brake tools you can make one.  This old brakes require them to fit almost perfectly befor you install the hubs.  If you can bowser this tool it’s a snap to pre adjust the shoes!  Jon

C35E299E-C072-4ED8-A2AE-D475302C755D.jpeg

Link to comment
Share on other sites

  • 2 weeks later...

No big updates.. 

 

Here is a photo of the front drum after the rust reformer on it.  I did not use electrolysis on these as there were bearings.. instead just lots of elbow grease to remove the majority of the surface rust, degreased the outside then I put on 2 coats of Rust-Oleum Rust Reformer (great stuff btw).  This is before adding black spray paint.

Tf6WtQZ.jpg

 

Got the wheels/tires on (well 3, misplaced the rear axle nut... it's around the garage somewhere)

BNS8Q5V.jpg

 

Helped clean up and sell my step-fathers 87 Silverado, had it out a day and was sold quick!

gcrCTEW.jpg

 

Also been working on rebuilding an engine for a '01 Mustang that is being turbocharged.

8G0ZHGn.jpg

 

Picked up a 25' roll of 3/16" NiCu brakeline, fittings, cutting tool, flaring tool, etc and possibly tomorrow going to put on new brake lines.

Edited by epix1718
  • Like 1
Link to comment
Share on other sites

On 5/14/2018 at 6:22 AM, Rustydodge46 said:

Hi  I found this amazing thread whilst in search of the bottom 42 grille trim, I don't suppose you have and spare or know the where abouts of a pair of left and right?  Loving the bull dogs too.  Classic!

FB_IMG_1520705008138.jpg

 

Thanks for the compliments.

Sorry I haven't seen that part but try asking jcmiller, I think he may have been selling that piece.. I check eBay very often so if I spot anything I'll send you a message. 

Edited by epix1718
  • Like 1
Link to comment
Share on other sites

On 5/14/2018 at 3:22 AM, Rustydodge46 said:

Hi  I found this amazing thread whilst in search of the bottom 42 grille trim, I don't suppose you have and spare or know the where abouts of a pair of left and right?  Loving the bull dogs too.  Classic!

FB_IMG_1520705008138.jpg

I do have those.  PM sent.

  • Like 1
Link to comment
Share on other sites

  • 11 months later...

Quick update, did some tuneup tasks (plugs, wires, ignition stuff), new oil, new coolant, some new hoses, new 6V battery.  Sprayed in some starter fluid into the untouched carb (which I soaked bolts in penetrating fluid so I may remove it tomorrow).  Neighbor is an old timer so he came over and helped me figure out the starter pedal.. which I had to press on REALLY hard for it to trigger so need to service that too.

 

Hearing it run was exciting though, last time I new it ran was 2003.  

 

I siphoned out the old fuel and it was very orange so not sure if rust or varnish (probably both).. either going to drop the tank and rinse it out best I can and use in-line filters, or purchase a repro tank and put that in.

Link to comment
Share on other sites

  • 8 months later...

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
×
  • Create New...

Important Information

We have placed cookies on your device to help make this website better. You can adjust your cookie settings, otherwise we'll assume you're okay to continue.

Terms of Use