Brandon S Posted July 28, 2013 Report Share Posted July 28, 2013 This part either came with the disassembled '42 P-14C or was bought with a set of misc '42 parts- can't remember. Now about done putting it all together but anybody out there have an idea what this is and where it goes?? Quote Link to comment Share on other sites More sharing options...
pflaming Posted July 28, 2013 Report Share Posted July 28, 2013 It looks like it might be a motor mount. Quote Link to comment Share on other sites More sharing options...
Oldguy48 Posted July 28, 2013 Report Share Posted July 28, 2013 Looks like a driveshaft carrier bearing. Quote Link to comment Share on other sites More sharing options...
randroid Posted July 28, 2013 Report Share Posted July 28, 2013 Gents, I'm guesing too, but I don't think it's either of the first two suggestions because it's too small and flexible for an engine mount, and wouldn't last long as a drive shaft mount because it's a bushing with no lube points. It looks more to be an alignment bearing for a floating part such as the shaft betwen the steering wheel and the worm gear. Does your car have a two-piece shaft for that application? -Randy Quote Link to comment Share on other sites More sharing options...
Dave72dt Posted July 28, 2013 Report Share Posted July 28, 2013 Looks like a brg in the center of it, Carrier brg for driveshaft Quote Link to comment Share on other sites More sharing options...
Brandon S Posted July 29, 2013 Author Report Share Posted July 29, 2013 It has a metal core bearing surrounded by a rubber mount and a bolted mount- I'll try to see if I have some mounting holes somewhere. Where on the driveshaft would this go? I have the OEM steering- one piece from wheel to the gearbox. Is it even for a 1940's Plymouth? Here's another one appears to be some sort of slotted bracket: under the dash? Engine compartment? ....any ideas? Quote Link to comment Share on other sites More sharing options...
Oldguy48 Posted July 29, 2013 Report Share Posted July 29, 2013 (edited) Brandon, If that first pic is indeed a driveshaft carrier bearing, I doubt that it fits your car. Typically, you would find one of those in a vehicle with a 2-piece driveshaft. It supports the driveshaft assembly at the center U-joint. I'm not knowledgeable about P14 vehicles, but doubt that it had a 2-piece driveshaft. The next item is a mystery to me, but it does resemble a track for an adjustable seat, although too short to be that. I'm sure someone will recognize it soon. Wayne Edited July 29, 2013 by Oldguy48 Quote Link to comment Share on other sites More sharing options...
_shel_ny Posted July 29, 2013 Report Share Posted July 29, 2013 2nd one for mounting coil ??, run dist. wires through tubes on each side?? Quote Link to comment Share on other sites More sharing options...
Frank Elder Posted July 29, 2013 Report Share Posted July 29, 2013 Sway bar mount? Quote Link to comment Share on other sites More sharing options...
JerseyHarold Posted July 29, 2013 Report Share Posted July 29, 2013 2nd one for mounting coil ??, run dist. wires through tubes on each side?? ^^X2. Quote Link to comment Share on other sites More sharing options...
Andydodge Posted July 29, 2013 Report Share Posted July 29, 2013 That 1st pic looks like a driveshaft centre bearing to me also........for the long wheelbase 7 passenger and limo mopars which did have a 2piece driveshaft.......andyd Quote Link to comment Share on other sites More sharing options...
Brandon S Posted July 30, 2013 Author Report Share Posted July 30, 2013 Ok, got one more I found- a pair of trim somethings with 2 mounting brackets on each- anybody out there might know what the heck this is?? Thanks. Quote Link to comment Share on other sites More sharing options...
Roadkingcoupe Posted July 30, 2013 Report Share Posted July 30, 2013 external sun visor mounts. Quote Link to comment Share on other sites More sharing options...
busycoupe Posted July 30, 2013 Report Share Posted July 30, 2013 I agree with Roadkingcoupe, the last pic looks like part of a sunvisor mount. The third pic looks like some kind of bracket that would be mounted with the wide side up. Used to hold something that would have to be removed easily....windshield washer reservoir perhaps? maybe to hold something in the trunk like part of the jack? Just guessing.. Dave Quote Link to comment Share on other sites More sharing options...
jboymechanic Posted July 30, 2013 Report Share Posted July 30, 2013 It has a metal core bearing surrounded by a rubber mount and a bolted mount- I'll try to see if I have some mounting holes somewhere. Where on the driveshaft would this go? I have the OEM steering- one piece from wheel to the gearbox. Is it even for a 1940's Plymouth? Here's another one appears to be some sort of slotted bracket: under the dash? Engine compartment? ....any ideas? Looks like it might be a track for a window regulator end, see if the mounting points match up to any two holes on any of your doors or inner rear quarter (depending if you have a coupe or sedan). Quote Link to comment Share on other sites More sharing options...
Brandon S Posted August 11, 2013 Author Report Share Posted August 11, 2013 Thanks everybody for your input, going to look for matching mounting holes one last time today and then they go to the junk pile. Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.