flathead31coupe Posted March 10, 2010 Report Share Posted March 10, 2010 (edited) in this pic, can someone tell me where the rubber o ring gasket goes, and the metal ring goes thanks, Edited March 11, 2010 by flathead31coupe Quote Link to comment Share on other sites More sharing options...
LuckyDevil Posted March 10, 2010 Report Share Posted March 10, 2010 hope this helps. I found it using the search at the top of the page. Quote Link to comment Share on other sites More sharing options...
flathead31coupe Posted March 10, 2010 Author Report Share Posted March 10, 2010 hope this helps. I found it using the search at the top of the page.where does g and e go.... Quote Link to comment Share on other sites More sharing options...
flathead31coupe Posted March 11, 2010 Author Report Share Posted March 11, 2010 anyone Quote Link to comment Share on other sites More sharing options...
Dodgeb4ya Posted March 11, 2010 Report Share Posted March 11, 2010 where does g and e go.... Look at this picture to see the correct order. The old original MoPar check valve had rubber ring G already built into it and that is why the picture does not show ring G. Rubber ring "G" assembles last after Check valve #18. Bob Quote Link to comment Share on other sites More sharing options...
flathead31coupe Posted March 11, 2010 Author Report Share Posted March 11, 2010 Look at this picture to see the correct order. The old original MoPar check valve had rubber ring G already built into it and that is why the picture does not show ring G. Rubber ring "G" assembles last after Check valve #18. Bob so it needs to go in there first, the the ck valve...what is E ring? Quote Link to comment Share on other sites More sharing options...
Dodgeb4ya Posted March 11, 2010 Report Share Posted March 11, 2010 so it needs to go in there first, the the ck valve...what is E ring? Assemble just as shown in the picture. "E" is just a thin round brass flat check valve washer that fits between the piston and the rear M/cyl cup. It controls brake fluid flow through several tiny holes drilled in the end of the piston on the return stroke. Bob Quote Link to comment Share on other sites More sharing options...
flathead31coupe Posted March 11, 2010 Author Report Share Posted March 11, 2010 in this pic, can someone tell me where the rubber o ring gasket goes, and the metal ring goes thanks, [ATTACH]16600[/ATTACH] sorry about that iam talking about this steel ring in the pic Quote Link to comment Share on other sites More sharing options...
flathead31coupe Posted March 11, 2010 Author Report Share Posted March 11, 2010 Assemble just as shown in the picture. "E" is just a thin round brass flat check valve washer that fits between the piston and the rear M/cyl cup. It controls brake fluid flow through several tiny holes drilled in the end of the piston on the return stroke.Bob thanks so i got this right the thick rubber ring G goes into the mc then the ck valve ect like the pic... thanks so much.... Quote Link to comment Share on other sites More sharing options...
flathead31coupe Posted March 11, 2010 Author Report Share Posted March 11, 2010 Look at this picture to see the correct order. The old original MoPar check valve had rubber ring G already built into it and that is why the picture does not show ring G. Rubber ring "G" assembles last after Check valve #18. Bob i see, thanks... Quote Link to comment Share on other sites More sharing options...
thrashingcows Posted February 17, 2011 Report Share Posted February 17, 2011 Just wanted to thank LuckyDevil for posting up this pic.... Turns out I neglected to install item "G". After I did this everything started working properly!! But I only have one thing to add about that picture. Everything is correct except for cup "C"...it actually goes between "D" and "E"....other then that the picture was a life saver....Thanks again!! Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.