Jump to content

garyp

Members
  • Posts

    135
  • Joined

  • Last visited

  • Days Won

    1

Everything posted by garyp

  1. I already have new lenses I bought them off e bay for 20 bucks that is how I found out I had the wrong bezels and buckets almost done with the project and I keep finding these little problems guys please keep your eyes open for me. I enclosed a couple of pics the ones I have are the taller of the two the correct one is the smaller one. Thanks Gary'
  2. I just discovered that someone through the years replaced my taillights with ones from a 1950 dodge wayfarer and I can not seem to find any originals for my 39 out there I have been an so many websites but no luck. Any ideas on what to do would be appreciated. Thanks Gary
  3. Thanks Don you are a great help to me and many others.
  4. Don are the pigtails voltage sensitive?
  5. Getting to the end on my 39 Dodge business coupe frameoff restro and am trying to find new sockets for tail and parking lights 6 volt not having any luck again any help would be appreciated.
  6. Yes Rich I was checking both sides yesterday and there is a big difference between the two I will be very specific when buying one thanks again Rich. Gary
  7. You are right Andy the one for my car mounts to a hole on the bottom of the a frame and the link has a stud sticking out of the bottom that goes through the hole and fastened with a nut. Gary
  8. Thanks Andy I will check that link if you don't put the exact words in your search it won't show. Gary
  9. Thanks Andy I have the old one but the hole in the top part where the sway bar goes in is worn out and there is rubber and what looks like brass or copper in there I will try and rig something up. Thanks again
  10. I just finished making new running boards for the car I guess I can make those my lenses are good the taillite themselves have a lot of pitting I guess I will work on them. Thanks
  11. Getting to the end of my 39 Dodge business coupe and have not been able to find a anti sway bar link or either new or used tail lites and the rubber base that goes under them or can I make the rubber bases but I don't know what they look like they were shot when I took them off. Again any help you guys can give will be appreciated. Gary
  12. Ok it is after the paint has cured, I never thought about the buffing wheel as always thanks for the advice. Gary
  13. Should I put the new fender welt on before paint or wait until after I really don't want to do anything to mess up the paint once it is done. ThanksGary
  14. Don you just lifted a weight off my chest I was so worried it was something serious and I would have to tear the engine apart. Thank you
  15. Just started my engine for the first time since being rebuilt and noticed a little anti freeze leaking from one of the intake manifold bolts I only ran the engine for about 15 seconds then shut it down. What could cause that maybe the stud where it goes in the block is not seating right? I will not start the engine until I hear from someone I am really worried about this. Thanks Gary
  16. Thanks guys I thought so I wonder why the book says different. You guys had my back again if I can ever help you let me know. Gary
  17. The brake line connector block mounted on the frame just in front of the master cylinder where the front and rear brake lines and master cylinder join what is that called it also has a switch or something on top that I guessed was a stop lite switch but my books wiring diagram call it a signal lamp switch with 1 wire going to the ampmeter and the other going to the dimmer switch can someone please set me straight on this I am afraid to hook up the wires until I am sure. Thanks in advance Gary
  18. Thanks Mike that's how I hooked them up hopefully its the same as yours. I am going to dive into the linkage hookup today and see if I can figure it out if you would send a pic that would be great thanks for the help. Thanks Gary
  19. Thanks guys Rich I would like to stop down and see you and your car how is next week for you let me know. My heater has 2 wires coming out one to the switch and the other is I assume the ground but my books have no info on it. Gary
  20. Can anyone tell me if my 39 Dodge came with a heater or was it an option I can't find any mention of it in my manuals I am trying to find out where the 2 wires coming out of it goes any help would be appreciated. Thanks Gary
  21. Putting my 39 back together and having a problem with the shifter linkage from the column to the trans doesn't seem to line up right and the pic I have in my book it looks like behind the shifter lever and the shifter cable there is a bracket between them and the trans but the pic is so hard to see I can't really tell and I don't have anything like it left over any pic's would be a big help. Thanks Gary
  22. Thanks guy's that is all I needed got the engine back from the machine shop and I didn't take any pic's of that particular area. I was hoping plugs went there I had no extra lines left over Don you saved the day again! Gary
  23. Can someone tell me what is supposed to be in the hole in the bottom of the block behind the generator and also the one just to the right of the oil filler and just left of the petcock I would appreciate any help. Thanks Gary
  24. garyp

    What is it

    Web master was correct it does fit in the timing cover thanks so much. Gary
×
×
  • Create New...

Important Information

We have placed cookies on your device to help make this website better. You can adjust your cookie settings, otherwise we'll assume you're okay to continue.

Terms of Use