wallytoo

if you are addressing the OP/thread starter, realize the thread is 7 years old, and the last activity, until yesterday, was 7 years ago.

had to slap on the chains to collect the last of the sap last weekend.. season is done... time for clean-up.

same.

good for the truck, and good for me, too. i always enjoy driving it, especially when hauling something.

maple season is a bit early for me this year, but that's our new weather. collected sap yesterday, and began boiling. should be drawing off syrup today. quick video of sap flow from one of the short lines, and pumping to the truck... sap flow & pumping

also, the canadian blocks were 25", not 23". so the length isn't going to be of much use in identifying the size.

it's all good! glad you got them done.

i thought you were asking about the inner fender, not the fender itself.

from what i recall, i installed mine from inside the hood, not from the wheel side. are you trying to install it from the wheel side?

when i first rebuilt the 237, circa 2009, i didn't touch the original oil pump. prior to the rebuild, running pressure was around 40 psi, and idle was around 15 psi. i was fine with those numbers. when the 237 threw a rod circa 2017, i pulled the pump and installed it on the "new" 251, although i did clean it and run oil through it prior to installing. pressure on the 251 is about 42 psi running, and 20 psi at idle. the original pumps are pretty solid, and work well enough. seems like a big risk to run a new pump if the original pump (or whatever pump came with a given engine) still works. in neither case did i submerge the pump in oil prior to installing, and it worked just fine (and pressure was indicated immediately during starting, prior to running).

dave erb was graybeard, and he died many years ago.

glad you still drive it, chris. i really enjoyed the posts for your arctic circle trip.

we cancelled our annual ice harvest day after rescheduling twice. open water at the edges (tough to drive onto the ice to load it), and not very thick for blocks - about 8 inches. last year, we had 18" blocks that weighed around 300 lbs each. from last year....

nice ride, robert! keep driving!

i have no idea how the 7.50s would be. my b1fa has 8.25x20s front and rear. never really thought it steered hard, though.

light work for the dodge the other day. i had dropped a big, almost dead maple from near my sap house, and didn't want to let the one decent log go to waste. so, i used the skidder to hoist the log onto the truck, and transported the log to the mill. compared to some of the loads i haul with it, this was a piece of cake!

for the zuk mod, the leaf springs and attaching points/shackles remain untouched, unlike ed's truck.

adding coils to a leaf spring suspension. it's a popular modification to 80s toyota trucks (rear leafs), using a coil that mounts around the spring rubber bumper. it was invented by a gearing dude who goes by "Zuk".

i see someone added the "zuk" mod to the rear suspension!

oh yeah. for whatever reason, this truck had a host of features that in subsequent years became options for most. it has twin sun visors, fresh air and mopar truck heater, triple bumper over-riders, extra fishbelly frame plates on the rear of the chassis, vacuum booster brakes, vacuum 2-speed eaton 1350, corner windows, hood ornament, etc. did not have a radio or ash tray, windshield washer, etc.

yeah, as bob notes, that's the factory firewall control. same one in mine, even though i have a smaller eaton 1350 2-speed.

hard to say, but it might be worth looking into. that's probably all related to the firewall control, and the adjustment of the cable there. fwiw, here's mine in low position...and the total movement up/down is only about an inch. again, could be all about the firewall mechanism adjustment.

rather than "J52", that shouid be "152", which is the nominal wheelbase. the truck in the picture looks to have a longer than "original" chassis, with a long bit of steel well beyond the rear wheels. can't help with the pattern, but i bet rob (dodgeb4ya) can!

no pics this time, but i loaded the last of the cordwood yesterday. turned out to be just over two cords. first time i've needed all 8 speeds available (4 & 2) to move a load. i never use 1 low, and rarely 1 high. same with 2 high. but, i needed them all to get it home. still stops excellent with all that weight; booster brakes are sweet! and i split that in two days with a maul.

mine are mounted like this....