Jump to content

Cpt.Fred

Members
  • Content Count

    1,737
  • Joined

  • Last visited

  • Days Won

    9

Everything posted by Cpt.Fred

  1. Cpt.Fred

    Another 230 build thread

    very cool, my fingers are crossed it runs as good as it looks!
  2. Cpt.Fred

    Time for an overhaul...

    nice piece. i'm using the AFR gauge from Innovate Motorsports
  3. Cpt.Fred

    Time for an overhaul...

    i will look into that. my experience is they move upwards pretty quickly once the butterflies open. by the way, you have to post a video of the car driving by and some more outside views of it
  4. Cpt.Fred

    Time for an overhaul...

    thank you Jim, great info once again. i really had hoped for a place to buy these parts new and in logical order from lean to rich, but i guess that would be too easy...🤣 i was running 159-59S mains in my triple carb setup on the 265. these were too lean at cruise. 159-61S were better, 14-14.5 AFR. the engine was drowning in fuel above 3000rpm and under heavy load in overdrive, i experienced 10,5-11 AFR, intolerable. i tried two sorts of step up jets, 149-113S (leaned out the cruise too much and still flooded under load) and 149- 43S (too much in general)... i can see the logic behind the numbers on the main jets, but the ones on the step ups don't quite add up for me. funny thing was that somehow the test results were not exactly what i had expected, especially changing the step ups had far bigger effects over the whole rpm range than i had thought before. good to know your measurements now, i will check the orifice diameters and then try soldering and drilling as well. another thing i did on my first triple setup on the old 201 was putting weaker springs into the step up jet assembly, allowing it to stay shut just a little longer. on the smaller engine that gave me pretty good results and the AFR was in an acceptable range. thanks for taking the time and sharing all your measurements! Fred
  5. Cpt.Fred

    Time for an overhaul...

    Jim, good job as always, i really love your car! speaking of jets, where do you get yours, and do you have a list that indicates which number jet is leaner or richer? i haven't found anything like that yet, and i would really like to see one. i always find it confusing to sort through the different mains and step ups and test drive them with the afr sensor, only to be confused again by their behaviour in the carb thanks, Fred
  6. Cpt.Fred

    230 Crankshaft source

    sorry, no spare crank here either. i'm going to call a few people and look around, though. watch ebay and classifieds closely, engines do turn up every once in a while, but getting pricey lately... best of luck to you! Fred
  7. Cpt.Fred

    anyone running Lake pipes on their P 15 or d24

    the car is air ride equipped
  8. Cpt.Fred

    Time for an overhaul...

    it purrs! sweeeeeet 🤗
  9. Cpt.Fred

    anyone running Lake pipes on their P 15 or d24

    a friend of mine recently built this. if you decide to use lake pipes, it's imperative to lower the car as much as possible to make it look good, imho. i think his car is gorgeous, but surely some might disagree.
  10. Cpt.Fred

    Time for an overhaul...

    so cool! i had compression seeping out at the beginning, too, but going through a few heat cycles and carefully retorquing it when hot fixed that. i think i retorqued four times and it always gave in a little until it finally sat right.
  11. Cpt.Fred

    The Maestro, George Asche Jr.!

    Ha, nice picture there, Walt! that sure was a great day, i would have loved to have more time to chat with you, it was all a little too much to take in at once for me, i must admit. we went to dinner that evening and then back to George's the next day and said goodbye and talked some more, but unfortunately we had a tough schedule to get on our way to the east. i hope you had a good time at Carlisle! best, Fred
  12. Cpt.Fred

    Time for an overhaul...

    ha, cool idea. still, i hope you don't have to touch those fittings too often later on :)
  13. Cpt.Fred

    Time for an overhaul...

    i'm jealous of you blasting cabinet nice work on the oil return and carb!
  14. Cpt.Fred

    Time for an overhaul...

    also, great work with the o-ring butterfly shafts! what's the story with the speedy sleeve and the balancer?
  15. Cpt.Fred

    Time for an overhaul...

    Jim, just like Andy i just stumbled upon the picture of your water pump rotor. i remembered, a guy i know from switzerland had cooling trouble on a mopar flathead, took the coolant pump apart, found one of those 2 blade rotors like yours in it and then decided to replace the pump with one of these models, like i have on the bench right here: afterwards he said he had a better cooling and more coolant flow, if i remember correctly. i have both chinese and oem pumps with the multi finned rotors, both have been working fine. maybe you want to consider a swap as well, regarding your turbo plans and everything... but hey, if the shop said it would be up to the task. hope he knew abouth the turbo i went for the 3/8" oil fitting on my oil filter swap and decided to run the line around to main oil gallery, so i did not have to drill the pump boss twice. looks good so far. can't wait until you fire yours up for the first time, keep up the great work! Fred
  16. Cpt.Fred

    Time for an overhaul...

    that's true, but i think it is a very narrow boss to drill the 2 holes in, like you did on your engine... don't know if i want to try to pull that off. plus we're running equal lenght tube headers, that take away lots of space. it's like a snake's nest on that side. but i haven't really decided yet, maybe i'll just measure some more and then go straight to copying your method :-) good one on the gear! the one i took out of mine is completely shot.
  17. Cpt.Fred

    Time for an overhaul...

    sure does help, very cool! thank you! where did you get that super nice original cam gear? i've gotten CNC'd ones the last time i ordered them new. i'll get my engine back from the shop next week, will do the full flow conversion and then start the assembly (after cleaning it for days on end ). i plan to drill the oil pump boss, plug it from underneath, get rid of the cross over tube in the crank case and instead enter the main oil gallery directly with an outside oil line. and now back to your thread!
  18. Cpt.Fred

    Exciting 1933 Dodge project!

    the documentary of the Peking- engine build on your FBpage is great. even more things to keep in mind, learning and taking notes here!
  19. Cpt.Fred

    Time for an overhaul...

    ok, that's a lot quicker than i'd thought. cool. thank you!
  20. Cpt.Fred

    Time for an overhaul...

    looking forward to your documentation of putting the timing gears and chain on in the correct way to get the valve timing right... i'm going to face the same challenge soon on a 230cui Dodge engine, this here will basically become my step by step manual to double check everything i'm doing. also i'm looking into getting a set of custom forged pistons for another engine, how long did it take JE to get yours made (the second time when they got it right)? I was also going to get a price estimate from Ross to see what they charge. yours aren't teflon coated or anything, are they? Fred
  21. Cpt.Fred

    Time for an overhaul...

    looking good! thanks for documenting your whole journey in this thread, and sharing all the pictures. a fine example of what internet message boards should be like. Fred
  22. Cpt.Fred

    Hi from England

    hey there, really nice car you got there greatings from Berlin, Fred
  23. Cpt.Fred

    Exciting 1933 Dodge project!

    fantastic project! you guys do great work... very cool! thanks for sharing.
  24. Cpt.Fred

    Shaving a 218 head vs. a standard 230 head?

    the pictures of the different chambers are very interesting, thanks for sharing. also, thanks for that milling chart, great info! i have a 1947 dodge 230 on the engine stand right now and the pistons on TDC are between 0,029" and 0,016" below the deck. also i never saw any of these engines having the pistons level to the deck from the factoy, yet. (but i admit i haven't seen more than 10 different ones)
×

Important Information

We have placed cookies on your device to help make this website better. You can adjust your cookie settings, otherwise we'll assume you're okay to continue.

Terms of Use