Jump to content

Phil Martin

Members
  • Posts

    432
  • Joined

  • Last visited

Everything posted by Phil Martin

  1. my dist looks like the two in pictures. parts store with books instead of puter shows this to be 51 distributor the 50 distributor shows points turned other way.
  2. My 50 dodge has a 51 dist the points work opposite from 50 dist.
  3. with plugs out should be able to turn with fan blade if it's not stuck.
  4. I sent you a PM about carb. Phil Martin
  5. thanks a lot for your help. I knew I had seen it onetime but thought it was on this site
  6. I have searched all over for how to convert slant six electronic distributor to use in 230 flathead. Could someone please tell me how to find it?
  7. Been to Iola 5 times. Love it but can't handle all that walking anymore.
  8. Thats what I think too. Not sure exactly how much oil I drained out. But I'm sure it was too much because now it works like it should. I measured 1 quart but not sure how much was left in pan.
  9. Your right. Lady in working in farm and home told me 1 qt was 4 pints. I might have taken out more than I thought. I'll put a little more in but it is shifting down like it should now. Thanks for the correction.
  10. I found my problem this morning. Operator probs happen a lot.about. About a year ago [yes it took a long time to find] I changed fluid in trans. Jacked car up from passenger side to get at trans plugs. Big mistake, suppose to have 3 pints 10 wt oil. I drained out 1.5 quarts of oil. Put in 3 pints 10 wt oil now it works fine. Sometimes feel like a fool this is one.
  11. I can't get my 50 dodge gyromatic to down shift unless I come to complete stop and push clutch in Shifts up ok but not down even if I floor it. Ran all electrical tests in manual and they all check out ok.
  12. my 50 dodge is 12 volts. I have a resistor and was still going thru points like crazy. I tested and was getting 10 volts from resistor to dist. I switched the wires around on resistor and now get 6 volts to dist.guy tell me resistror is the same either way but this is the way it tests. Car is running way better and points haven't burnt out since I did it.
  13. My 50 dodge didn't start. Unhooked the wire from coil to the, can't think what it's called not, on the aircleaner bracket where wires go to carb and trans. Now starts better than it ever did. If I come eo complete stop it will shift down, take off and let up on gas and it shifts up. The only thing it doesn't do is if I slow down and floor it no down shift.
  14. Be carefull when you take it off. The pin worked out on mine and when I took it off I wasn't carefull and the arm which the pin holds fell into the pan.
  15. Yes when I replaced wires because it would't shift. Now it would't even start. I suspect the interuptor switch may be bad.
  16. As I have said before I have the power to the circuit breaker un hooked. In low range I start out in 1st gear push clutch in and it shifts to 2nd gear . I push clutch in when I stop and it always starts in 1st. After it shifts to 2nd I shift the lever to high range. It goes to 4th gear because speed is to fast for 3rd. If I stop and push clutch in and speed engine just a little it will start out in 3rd and shift to 4th by letting up on gas. This all works with no elec power going to trans. I have gyromatic which I believe is same as m6. So they all should work like mine does.
  17. I replaced my radiator when I got my dodge. I believe it is for a mustang. Diminsions worked out for dodge. It runs on warm side in hot weather, would it hurt to put about 4 lb cap on it? It's a new radiator.
  18. I had trouble with mine dying and not starting. I unhooked the wire from coil to circuit breaker and it starts great. I can take off and then push clutch and it will upshift. Possible have a problem with interuptor switch? Haven't looked into that yet. If yours wont shift til 25 mph the idle is to high.
  19. $5000 is an unbelieveable price with all that has been done to it. Somebody should jump on that!
  20. When you take off then push clutch in and it should shift up. Mine was not shifting but would if i pushed clutch in. changed solenoid on trans and not works good. Some times i push clutch in just because it will shift a lot faster.
  21. Mine does the same thing when taking off under those conditions. Misses for just a few seconds then runs great. Only time it misses. Haven't found a reason for it. If I use the clutch when stopped it takes off fine.
  22. I agree it's a 1950 like mine. is it gyromatic or 3 speed behind fluid drive?
  23. When I put 6 volt pump on my dodge I checked fuel pressure at 16 lbs. Put a regulator on it for sure.
  24. Must be real fun to get those back wheels off.
×
×
  • Create New...

Important Information

We have placed cookies on your device to help make this website better. You can adjust your cookie settings, otherwise we'll assume you're okay to continue.

Terms of Use